Selection of 10 products among
10
ANIT SLIP TAPES
GRIPFAST® anti slip tape provides an immediate DIY solution to the problem of slip hazards. Recommended for use internally and for pedestrian traffic it has a ‘near diamond hard’ aggregate and a
conformable pressure sensitive adhesive giving strong adhesion to most surfaces.
Product range:
• Rolls: 18.25m x 19mm, 25mm, 50mm, 100mm, 150mm, 305mm and 610mm.
• Tiles: 140mm x 140mm (pack of 10).
• Treads: 19mm x 610mm (pack of 10). 150mm x 610mm (pack of 10).
•Primer: 1 litre tin.
• Edge Sealer: 100ml tube.
Colours:
• Standard: Black, yellow, hazard (black and yellow), neutral and photoluminescent.
• Specific BS and RAL colours available on application.
Product grades:
• Standard, Aqua and Resilient.
Product benefits:
• Suitable for use on most surfaces including wood, concrete, steel and chequer-plate.
•Water and solvent resistant.
• Suitable for steam and detergent cleaning.
>>>
View the product on gripfast.co.uk
Polydeck Ltd
CORDUROY TACTILE
GRIPFAST® Corduroy Tactiles are designed to warn visually impaired people of the presence of hazards, such as stairs, level crossings or the approach to on-street light rapid transit (LRT)
platforms. GRIPFAST® Corduroy Tactiles convey the message hazard, proceed with caution.
The profile of the corduroy surface comprises rounded bars running transversely across the direction of pedestrian travel. The bars are 6mm high, 20mm wide and spaced 50mm from the centre of one bar to the centre of the next.
GRIPFAST® Corduroy Tactiles are made from a durable GRP (glass reinforced polyester) sheet incorporating a near diamond hard aggregate for a long life span.
Product thickness:
• 4mm base plus 6mm bars.
Colours:
• Standard: buff or grey. Tactiles must be a contrasting colour to the existing substrate. • Specific BS and RAL colours available on application.
Standard tile size:
• 800mm x linear metre.
Product benefits:
• Manufactured from durable, GRP sheet.
• Incorporates a ‘near diamond hard’ aggregate to give a hardwearing anti slip surface.
• Good resistance to impact damage and will not shatter in normal use.
• Satisfies the requirements of The Building Regulations 2000 Section 1.33.c
• Conforms to DETR guidelines.
• Can be easily glued and/or screwed down to virtually any surface, eliminating the need for time consuming and costly excavation.
• Chamfered edge profile ensures Tactiles do not pose a trip hazard. Extract from The Building Regulations 2000 Section 1.33c: A stepped access will satisfy requirement M1 or M2 if... ‘a ‘corduroy’ hazard warning surface is provided at top and bottom landings of a series of flights to give advance warning of a change in level.
>>>
View the product on gripfast.co.uk
Polydeck Ltd
GRIPDECK TIMBER PANELS
Gripdeck™ timber panels are a tailor-made range of load-bearing and overlay anti slip panels designed for use on a variety of applications including station platforms, bridges, ramps, point board
covers, track crossings and factory floors.
Manufactured from Finnish birch throughout plywood which conforms to BS5268, the panels are fully resin encapsulated and dressed with a near-diamond hard aggregate to give a typical design life of 10 years.
A range of panels thicknesses, aggregate grades, colours and edge finishes are available: tactile surfacing and 'colour constant' high speed lines can also be incorporated for rail applications,
Resistant to oil and grease, the panels are suitable for both internal and external use.
Product thickness:
• Overlay Applications: ø 9mm, 12mm, 18mm.
• Load-bearing Applications: ø 18mm, 24mm, 30mm 48mm.
Aggregate grades:
• Barefoot, Pedestrian, Heavy Industrial.
Colours:
• Standard: black, yellow, blue.
• Specific BS and RAL colours available on application.
Maximum sheet size:
• 2440mm x 1220mm - overlay panels
• 3660mm x 1525mm - load-bearing panels
Product benefits:
• A tried and tested method of providing both overlay and structural decking at a reasonable cost,
• Panels are tailor-made to specific requirements and are available in a choice of grades, colours, sizes and edge and nosing details.
• Fixings holes are pre-drilled and countersunk to help speed up installation.
• Resin sealing kits are provided to seal holes after fixing and to help prolong panel life.
• Panels are resistant to oil and grease and most chemicals
>>>
View the product on gripfast.co.uk
Polydeck Ltd
OFF-STREET BLISTER TACTILE
GRIPFAST® ‘Off-Street’ Blister Tactiles are designed to warn visually impaired people of the edge of all ‘off-street’ railway platforms.
The product consists of offset rows of flat-topped blisters
5mm high, spaced 66.5mm apart from the centre of one blister to the centre of the next.
GRIPFAST® ‘Off-Street’ Blister Tactiles are made from a durable GRP (glass reinforced polyester) sheet incorporating a ‘near diamond hard’ aggregate for a long life span.
Two varieties of tactile are available; 1mm thick for bonding to level surfaces and 4mm thick for bonding or mechanicallyfixing to more uneven surfaces.
Product thickness:
• 1mm, 4mm base plus 5mm blister.
Colours:
• Standard: buff or grey. Tactiles must be a contrasting colour to the existing substrate.
• Specific BS and RAL colours available on application.
Standard tile size:
• 400mm x linear metre
Product benefits
• Manufactured from durable, GRP sheet.
• Good resistance to impact damage and will not shatter in normal use.
• Incorporates a ‘near diamond hard’ aggregate to give a hardwearing anti slip surface.
• Tested by the Transport Research Laboratory for the Joint Mobility Unit and used by Railtrack plc and Network Rail.
• Conforms to DETR guidelines.
• Can be easily glued and/or screwed down to virtually any surface, eliminating the need for time consuming and costly excavation.
• Chamfered edge profile ensures Tactiles do not pose a trip hazard.
>>>
View the product on gripfast.co.uk
Polydeck Ltd
STANDARD FLAT SHEETS
GRIPFAST® Standard Flat Sheets are a rigid finished product made from durable GRP (glass reinforced polyester) coated with a ‘near diamond hard’ aggregate.
They are designed to be mechanically
fixed over virtually any structurally sound and level substrate including wood, concrete, steel, chequer-plate and open grating.
Resistant to oil and grease, they are suitable for both internal and external use.
GRIPFAST® Standard Flat Sheets have a design life of 30 years.
Product thickness:
• Nail Down 2mm.
• Standard 4mm.
Product grades:
• Barefoot, Pedestrian, Industrial and Heavy Industrial.
Colours:
• Standard: black, yellow, grey, red, blue, green and brown.
• Specific BS and RAL colours available on application.
Maximum sheet size:
• 2440mm x 1220mm.
Product benefits:
• Quick to mechanically install with little downtime and can be walked on immediately.
• Can be cut on site without the need for remedial repairs.
• Lighter and easier than timber panels to transport and move around.
• Fixing screws do not need to be sealed.
• Available in fire resistant format.
>>>
View the product on gripfast.co.uk
Polydeck Ltd
