Thermoforming :
48 products
INSULATION - ALREFLEX PLATINUM
Alreflex Platinum
High performance partial fill cavity insulation and rain barrier
An all encompassing cavity wall solution to Part L 2006 and Part 6 Scottish Standards
A 50mm thickness of
Alreflex Platinum can achieve a U-Value better than 0.35W/m2K in a 100mm cavity using any 100mm standard medium density block.
This detail will still meet the requirements of the new Part L 2006 based on current information.
Available in a range of thicknesses to meet the various building regulations requirements. (See U-Value solutions on back page.)
BBA Certificated Platinum board laminated to BBA Certificated Alreflex 1L-1 Super R Class O of which approximately 4 million sq.m. has been successfully installed in UK housing.
Special overlapping joints secured by wall tie clips creating a waterproof rain barrier to prevent ingress of water across the cavity.
Continuous overlapping system to aid air tightness of wall.
1200 x 450 boards installed as standard cavity wall boards but with laps secured on wall ties.
Installation ProcedureWalls are constructed in the conventional manner with special Alreflex wall ties spaced at 450mm vertically and 900mm horizontally. Alreflex Platinum is installed on top of a run of wall ties in the normal way with the lap slit with a knife at the wall-ties to allow the flap to run past the wall-tie and lie flat on the board.
Secure the board with the clips in the normal way. The special downstand on the Alreflex wall ties takes up any possible vertical pressure experienced when installing the boards and clips.
Cavity wall insulation and rain barrier. Laps provide a continuous water proof barrier against the ingress of rainwater etc.
25mm Board achieves: U = 0.35W/m2K with 100mm (K=0.11) aerated block
Achieves Part L 2006 requirements with a minimum 75mm cavity in most house types.
50mm Board achieves: U = 0.35W/m2K with 100mm concrete block
U = 0.30W/m2K with 100mm (K=0.19) aerated block
Can achieve Part L 2006 requirements with a minimum 100mm cavity in most house types.
Extensions in England & Wales; U Value of 0.30 is the elemental value for walls in extensions based on Part L 2006 *These details are especially suitable for high rise and commercial buildings.
U = 0.27W/m2K with 100mm (k=0.11) aerated block
Extensions in Scotland; U Value of 0.27 is the elemental value for walls in extensions based on Part 6 Scottish Standards
50mm THICK ALREFLEX PLATINUM CAVITY BOARD WITH ALREFLEX 1L1 DRY LINING OR THERMAL LAMINATE BOARD
Cavity wall insulation and rain barrier with high performance dry lining and vapour barrier. Laps provide a continuous water proof barrier against the ingress of rain water etc. U = 0.25W/m2K with 100mm (K=0.19) aerated block.
Suitable for all areas and projects where a low U-value is required (i.e. in electrically heated flats etc.)
High comfort level with quick heat-up period.
Also suitable for 3-storey housing and flat construction.
Ideal for all exposure areas.
Please note: If a laminated board with a dot and dab fixing is preferred to the 1L1 DRY LINING detail shown, please contact our technical department for suitable boards and thicknesses.
>>>
View the product on springvale.com
Springvale EPS Ltd
ANTI FOULING - CUPROMARK
The Dunlaw Cupromark marine antifouling marker system was developed alongside its sister product Cuproprene in response to the Oil & Gas Industry's requirement, for long term underwater asset and
apparatus identification. The Cupromark range of markers maximises effective use of diver ROV, AUV and DSV time, during inspection, repair and maintenance.
The markers can be installed on offshore steel or concrete structures, templates, manifolds, Xmas trees, wellheads, spoolpieces, pipelines, and umbilicals to name but a few.
The antifouling capability of Cupromark is the result of extensive testing and research for over 20 years.
In order to provide permanent subsea identification, markers must remain clear of marine growth throughout the lifetime of the offshore/subsea structure. This performance is achieved by exploiting the antifouling properties of copper.
Cupromark antifouling material consists of a monolayer of cupro-nickel granules (1mm dia and 1 mm long) embedded and chemically bonded into the surface of a 3 mm thick Polychloroprene rubber sheet. The copper nickel used has excellent corrosion and antifouling properties as well as higher erosion resistance than other 90/10 alloys. The bulk of the cupro-nickel remains below the surface of the marker and the antifouling effect continues at a controlled rate over many years.
Cupromark markers are pigmented in high visibility yellow (background) and black (character colour). Visibility tests carried out have proven this colour combination to the most effective, and this has been adopted as standard.
Specially developed installation systems are available for securing the markers, including vulcanising, cold bond adhesives and a variety of strapping systems.
>>>
View the product on dunlaw.com
Dunlaw Engineering Ltd
JOHNSON CONTROLS A19BAG-1 THERMOSTAT
Johnson Controls A19BAG-1C Thermostat for Portable Heaters with Extension Cord & Chain Hanger
Description
Sturdy compact thermostat designed especially for temporary installations.
Features
6
foot extension cord with piggyback style plug
NEMA 1 enclosure
chain mount
Switch Action: SPST Open High No Heat Position
Range: 35 to 95°F (2 to 35°C)
Diff 3°F (1.7°C) Non-Adj.
Max. Bulb Temp. 140 °F (60°C)
Applications
on/off control of portable space heaters
agriculture
Electrical Motor Ratings 120VAC:
AC Full Load 15 Amp
AC Locked Rotor 90 Amp
Application
The A19BAG special thermostat for portable heaters is a singlepole, single-throw control with contacts opening on a rise in temperature. The thermostats are supplied with an adjustable range and a fixed differential. A No Heat position on the dial permits manual shutdown of the heater without disconnecting the thermostat or the power supply. A special 3-wire extension cord and series plug are an integral part of this control to permit plugging the heater cord into the thermostat extension cord for automatic operation. A beaded chain hanger is supplied to permit supporting the thermostat in any convenient location.
All Series A19 thermostats are designed for use only as operating controls. Where an operating control failure would result in personal injury and/or loss of property, it is the responsibility of the installer to add devices (safety, limit controls) or systems (alarm, supervisory systems) that protect against, or warn of, control failure.
General Description
The A19BAG is a sturdy, compact thermostat with a visible scale and an adjustable set point knob. An exposed helical sensing element is specially designed and field proven for rapid response and dependability. The enclosed snap-acting contacts are dust protected. The thermostat has a NEMA Type 1 enclosure and is designed for portable heater applications. A strain relief bushing on the extension cord minimizes undue strain on the wire connections at the terminals.
>>>
View the product on infraredheaters.com
Infrared Internationale Engineering
