Thermal processing: suppliers, wholesalers and manufacturers on Hellopro
Search   


Thermal processing :

671 products
Select the category
Selection of 79 products among 671
THERMAL MATERIAL GAP PAD VO

THERMAL MATERIAL GAP PAD VO
Thermal conductivity: 0.8 W/m-K Enhanced puncture, shear, and tear resistance Easy material handling Electrically isolating Gap Pad VO is a cost effective thermally conductive interface. The material is a filled thermally conductive polymer supplied on a rubber coated fiberglass carrier allowing for easy material handling. The conformable nature of Gap Pad VO allows the pad to fill in air gaps between PC boards and heat sinks or a metal chassis. The resultant thickness of the Gap Pad will determine the thermal resistance. Subtracting the initial gap pad thickness by the deflection value, obtained above, will give the resultant thickness. Refer to the graph below to obtain the thermal resistance of the material. >>>
View the product on bergquistcompany.com Bergquist
THERMAL ASSEMBLIES

THERMAL ASSEMBLIES
Fully integrated temperature control assemblyConsisting of an integrated, fan, heatsink, TEC and thermal block, these can either provide unregulated heat pumping, heating or cooling when used with just a power supply. Or if used with a temperature controller can be temperature stabilized.SpecificationThere are several standard thermal heat pump ratings, however, other combinations and peltier types are available on request. * 20W Heat Pump - 12V operation at 2.4A using a 25 x 25mm 20W Peltier * 40W Heat Pump - 12V operation at 4.1A using a 30 x 30mm 40W Peltier * 80W Heat Pump - 12V operation at 8.6A using a 40 x 40mm 80W Peltier. >>>
View the product on electrondynamics.co.uk Electron Dynamics Ltd
THERMOELECTRIC SUBSYSTEMS AND THERMAL CONTROL SOLUTIONS

THERMOELECTRIC SUBSYSTEMS AND THERMAL CONTROL SOLUTIONS
Ferrotec has worked with select customers to develop integrated thermoelectric subsystems and assemblies that use peltier coolers for thermal management in high-volume applications. Leveraging our expertise in thermal solutions and thermoelectric systems, we have been successful in helping our customers identify integrated solutions that enable new products, improve system precision, and reduce costs. >>>
View the product on ferrotec.com FerroTec
THERMAL MANAGEMENT

THERMAL MANAGEMENT
Flat conductors have a much greater surface to volume ratio than round wire. This extra surface area facilitates the dissipation of heat away from the circuit: heat is easily dissipated from both sides of the flexible circuits, the thin polyimide dielectric permitting a relatively easy thermal path. In rigid boards the dielectric substrate is a thermal insulator inhibiting the flow of heat, and this can be a reason to substitute using flex. >>>
View the product on flexibletechnology.com Flexible Technology Limited
THERMAL AGEING (ENDURANCE) IN AIR OVEN

THERMAL AGEING (ENDURANCE) IN AIR OVEN
Product Description Thermal Ageing. - 6 Cell System + Stainless Steel Construction with Removable Sealed Lids + Individual Air Flow Meters +Individual Cell Timer + Oil Bath with 3 Term PID Controller + Twin Archemedean Oil Pumps +Over Temperature Thermal Cut Out. Test Description Test sample are suspended in a precisely controlled environment with temperature controlled air continually being circulated through each Test Cell at a constant flow. The Test Samples are checked for Thermal Aging at set Time Intervals and the condition recorded. Part Numbers RR/TAA Complies with Standard(s) BS 903, BS 6746, BS 5691, ASTM E95 >>>
View the product on ray-ran.com Ray-Ran Test Equipment Ltd
ACTIVE THERMAL MANAGEMENT - THE COOL-IT II

ACTIVE THERMAL MANAGEMENT - THE COOL-IT II
Ideal for amps, receivers and almost anything else that could overheat inyour system. They’re easy to install; just center the unit above the heat sinks and plug the power supply into an AC outlet. A soothing stream of cool air quietly flows down and between the heat sink fins lowering the temperature to more tolerable levels. The Cool-It is your solution for equipment housed within partially enclosed cabinets. Controlled by a thermal switch, Cool-It II is fully automatic. >>>
View the product on rotechsystem.com Rotech Systems
THERMAL MATERIALS - SIL-PAD K-10

THERMAL MATERIALS - SIL-PAD K-10
Thermal impedance: 0.41°C-in2/W (@50 psi)Tough dielectric barrier against cut-throughHigh performance filmDesigned to replace ceramic insulatorsSil-Pad K-10 is a high performance insulator. It combines special film with a filled silicone rubber. The result is a product with good cut-through properties and excellent thermal performance.Sil-Pad K-10 is designed to replace ceramic insulators such as Beryllium Oxide, Boron Nitride, and Alumina. Ceramic insulators are expensive and they break easily. Sil-Pad K-10 eliminates breakage and costs much less than ceramics. >>>
View the product on bergquistcompany.com The Bergquist Company
VERTICAL THERMAL CURING OVENS - ULTIMA™ II

VERTICAL THERMAL CURING OVENS - ULTIMA™ II
The Ultima II Vertical Curing system is configurable for continuous inline curing of components in magazines, carriers, strips, baskets or other transport mediums. The superior oven design ensures excellent thermal performance utilizing the smallest automated equipment footprint in the industry. The vertical format enhances in-line integration to any process equipment. Process flexibility is achieved via nine separate curing chambers with independent controllers for temperature, airflow and exhaust for effluent gases. The Ultima II is easily integrated with other process equipment or can be used as a stand alone system. >>>
View the product on thermalproductsolutions.com TPS Groupe - SPX Corporation
THERMAL MATERIAL GAP PAD HC1000

THERMAL MATERIAL GAP PAD HC1000
Thermal conductivity: 1.0 W/m-K Highly conformable, low hardness “Gel-Like” modulus Fiberglass reinforced for puncture, shear and tear resistance Gap Pad HC 1000 is an extremely conformable low modulus polymer that acts as a thermal interface and electrical insulator between electronic components and heat sinks. The “gel-like” modulus allows this material to fill air gaps to enhance the thermal performance of electronic systems. Gap Pad HC1000 is offered with removable protective liners on both sides of the material. The resultant thickness of the Gap Pad will determine the thermal resistance. Subtracting the initial gap pad thickness by the deflection value, obtained above, will give the resultant thickness. Refer to the graph below to obtain the thermal resistance of the material. >>>
View the product on bergquistcompany.com Bergquist
ACTIVE THERMAL MANAGEMENT - SYSTEM 3TM

ACTIVE THERMAL MANAGEMENT - SYSTEM 3TM
The System 3 is for smaller systems like a receiver and one or two other components in a small cabinet.Typically, small systems do not need large volumes of air to remove the heat they generate. The System 3 moves 15 to 20 cubic feet of air per minute, and replaces the air typically twice a minute, more than enough for systems of even greater power.When your budget is tight, the System 3 may be just the answer. It is comprised of two high-quality 3.125” fans, grilles, a plug-type power supply, a thermal switch, and a terminal strip pre-mounted in a small box for interconnections. It is easy to install, and can either be arranged to pull cool air in or push heated air out. >>>
View the product on rotechsystem.com Rotech Systems
THERMAL MATERIALS - SIL-PAD 400 (7 MIL)

THERMAL MATERIALS - SIL-PAD 400 (7 MIL)
Sil-Pad 400 is a composite of silicone rubber and fiberglass. The material is flame retardant and is specially formulated for use as a thermally conductive insulator. The primary use for Sil-Pad 400 is to electrically isolate power sources from heat sinks.Sil-Pad 400 has excellent mechanical and physical characteristics. Surfaces are pliable and allow complete surface contact with excellent heat dissipation. Sil-Pad 400 actually improves its thermal resistance with age. The reinforcing fiberglass provides excellent cut-through resistance and Sil-Pad 400 is non-toxic and resists damage from cleaning agents. >>>
View the product on bergquistcompany.com The Bergquist Company
THERMAL PROTECTORS - 7AM SERIES

THERMAL PROTECTORS - 7AM SERIES
The Klixon®7AM thermal protector prevents overheating in a variety of consumer, industrial and commercial products. It is a miniature, snap acting, thermally operated device that's a proven performer in protection technology. It is the right choice for applications where available space is at a premium. Thermtrol can provide these units with a variety of leads, terminations and insulating sleeves to meet your specific requirements, including nickel strip leads for NI-CAD battery packs. >>>
View the product on thermtrol.com ThermTROL
THERMAL MATERIAL GAP PAD 1000SF

THERMAL MATERIAL GAP PAD 1000SF
Thermal conductivity: 0.9 W/m-K No silicone outgassing No silicone extraction Reduced tack on one side to aid in application assembly Gap Pad 1000SF is a thermally conductive, electrically-insulating, silicone-free polymer specially designed for silicone-sensitive applications. The material is ideal for applications with high stand-off and flatness tolerances. Gap Pad 1000SF is reinforced for easy material handling and added durability during assembly. The material is available with a protective liner on both sides of the material. The resultant thickness of the Gap Pad will determine the thermal resistance. Subtracting the initial gap pad thickness by the deflection value, obtained above, will give the resultant thickness. Refer to the graph below to obtain the thermal resistance of the material. Typical Applications Include Digital disk drives Automotive modules Fiber optics modules >>>
View the product on bergquistcompany.com Bergquist
ACTIVE THERMAL MANAGEMENT - SYSTEM 1

ACTIVE THERMAL MANAGEMENT - SYSTEM 1
Our most powerful and flexible heat problem-solving device. This extraordinarily quiet air mover can be mounted to almost any enclosure. The System 1 comes complete with tubing that is compatible with tubing-to-surface adapters* of different sizes (6” square to 14” square). Designed to move over 100 cubic feet of hot air per minute, the precision-balanced impeller produces little sound, even at full speed (as measured by ISO standard 3744, it’s 8dB quieter than industrial supply bathroom ventilators). The basic system includes the fan, 8’ of acoustically insulated flexibletubing, mounting brackets, clamps, and a 6” sq. hot air collector. Available accessories include thermal switches, speed controls, extra tubing and a wide variety of fittings. >>>
View the product on rotechsystem.com Rotech Systems
THERMAL MATERIALS - SIL-PAD A2000 (20 MIL)

THERMAL MATERIALS - SIL-PAD A2000 (20 MIL)
Thermal impedance 0.32°C-in2/W (@50 psi)Optimal heat transferHigh thermal conductivity 3.5 W/m-KSil-Pad A2000 is a conformable elastomer with very high thermal conductivity that acts as a thermal interface between electrical components and heat sinks. Sil-Pad A2000 is for applications where optimal heat transfer is a requirement.This thermally conductive silicone elastomer is formulated to maximize the thermal and dielectric performance of the filler/binder matrix. The result is a “grease-free”, conformable material capable of meeting or exceeding the thermal and electrical requirements of high reliability electronic packaging applications. >>>
View the product on bergquistcompany.com The Bergquist Company
THERMAL MATERIAL GAP PAD VO SOFT

THERMAL MATERIAL GAP PAD VO SOFT
Thermal conductivity: 0.8 W/m-K Conformable, low hardness Enhanced puncture, shear and tear resistance Electrically isolating Gap Pad VO Soft is recommended for applications that require a minimum amount of pressure on components. Gap Pad VO Soft is a highly conformable, low modulus, filled-silicone polymer on a rubber-coated fiberglass carrier. The material can be used as an interface where one side is in contact with a leaded device. The resultant thickness of the Gap Pad will determine the thermal resistance. Subtracting the initial gap pad thickness by the deflection value, obtained above, will give the resultant thickness. Refer to the graph below to obtain the thermal resistance of the material. Typical Applications Include Telecommunications Computer and peripherals Power conversion Between heat generating semiconductors or magnetic components and a heat sink Area where heat needs to be transferred to a frame, chassis, or other type of heat spreader >>>
View the product on bergquistcompany.com Bergquist
ACTIVE THERMAL MANAGEMENT - THE COOL-CUBE™

ACTIVE THERMAL MANAGEMENT - THE COOL-CUBE™
A new product, Cool-Cube, has been developed for the home theater design and installation community. Combining a compact power module with 4" flexible tubing, Cool-Cube will pull heated air out of a closed mid-size cabinet and quietly move it to a nearby closet, utility room, etc. (3” and 2” tubing is also available.)The power module is controlled by a 2-stage thermal switch that turns the power module on at low speed at 92 degrees (F) and switches it to high speed at 102 degrees. The noise generated is very low; why trade a heat problem for a noise problem?Cool-Cube's power module should be placed at the exhaust end of the tubing. A small flange at the suction end of the tubing is easily connected to a flat surface, such as the back of a cabinet.Order the Cool-Cube with 4" tubing if clearance allows, or with our smaller diameter tubing for those really tight situations. (While the 4" tubing allows greater air flow, the smaller tubing will ventilate normal heat loads in typical cabinets. In all cases, you should use the largest size tubing possible.) >>>
View the product on rotechsystem.com Rotech Systems
THERMAL MATERIALS - SIL-PAD 900S

THERMAL MATERIALS - SIL-PAD 900S
Thermal impedance: 0.61�C-in2/W (@50 psi)Low mounting pressuresSmooth and highly compliant surfaceElectrically isolatingGeneral-purpose thermal interface material solutionThe true workhorse of the Sil-Pad product family, Sil-Pad 900S thermally conductive insulation material is designed for a wide variety of applications requiring high thermal performance and electrical isolation. These applications also typically have low mounting pressures for component clamping.Sil-Pad 900S material combines a smooth and highly compliant surface characteristic with high thermal conductivity. These features optimize the thermal resistance properties at low pressure.Applications requiring low component clamping forces include discrete semiconductors (TO-220, TO-247 and TO-218) mounted with spring clips. Spring clips assist with quick assembly and apply a limited amount of force to the semiconductor. The smooth surface texture of Sil-Pad 900S minimizes interfacial thermal resistance and maximizes thermal performance. >>>
View the product on bergquistcompany.com The Bergquist Company
THERMAL PROTECTORS - SELF-HOLD 7AM SERIES

THERMAL PROTECTORS - SELF-HOLD 7AM SERIES
Thermtrol's Self-Hold 7AM manual reset thermal protector combines the protection of the Klixon® 7AM with a self-holding feature. Designed to prevent overheating in a variety of consumer, industrial and commercial products, it is a miniature, snap-acting, thermally operated device that once opened, on temperature rise, will maintain its open state until power is removed. At that point, the device will automatically reset. It's the right choice for applications where available space is at a premium, eliminating the need for a reset button. Thermtrol can provide these units with a variety of leads, terminations and insulating sleeves to meet your specific requirements. >>>
View the product on thermtrol.com ThermTROL
THERMAL MATERIAL GAP PAD VO ULTRA SOFT

THERMAL MATERIAL GAP PAD VO ULTRA SOFT
Thermal conductivity: 1.0 W/m-K Highly conformable, low hardness "Gel-like" modulus Designed for low-stress applications Puncture, shear and tear resistant Gap Pad VO Ultra Soft is recommended for applications that require a minimum amount of pressure on components. The viscoelastic nature of the material also gives excellent low stress vibration dampening and shock absorbing characteristics. Gap Pad VO Ultra Soft is an electrically isolating material, which allows its use in applications requiring isolation between heat sinks and high voltage, bare leaded devices. The resultant thickness of the Gap Pad will determine the thermal resistance. Subtracting the initial gap pad thickness by the deflection value, obtained above, will give the resultant thickness. Refer to the graph below to obtain the thermal resistance of the material. >>>
View the product on bergquistcompany.com Bergquist
ACTIVE THERMAL MANAGEMENT - THE COOL-VENT™ FAMILY

ACTIVE THERMAL MANAGEMENT - THE COOL-VENT™ FAMILY
The popularity of our Original Cool-Vent™ has spawned a complete family of three Cool-Vent products:- The Cool-Vent I (The Original Cool-Vent)- The Cool-Vent II- The Cool-Vent III If you are unfamiliar with what a Cool-Vent does, the concept is simple. It is an attractive solid wood grille with fans discretely hidden behind it that either pull cooling air in or push hot air out. It elevates the idea of passive ventilation into the realm of controlled cooling. There are 26 different woods available that can be finished to match built-in cabinets or fine furniture.The primary differences among the three Cool-Vent products are size and capacity. Cool-Vent I is controlled by a thermal switch that activates at 90 degrees F. (This is a single-speed product.) Cool-Vent II and III are controlled by a dual thermal switch assembly that turns on the fans at 90 degrees F and switches to a higher (but still quiet) speed at 100 degrees F. >>>
View the product on rotechsystem.com Rotech Systems
THERMAL MATERIALS - SIL-PAD 1750

THERMAL MATERIALS - SIL-PAD 1750
Thermal impedance: 0.53°C-in2/W (@50 psi)Excellent dielectric strength retention after humidity exposureElastomeric padThe combination of high thermal conductivity and excellent dielectric strength retention after humidity exposure is formulated into the Sil-Pad 1750 elastomeric pad.Sil-Pad 1750 relies on processes that minimize the effect of high humidity on the electrical properties of finished material. Therefore, exposure to humid environments during assembly, or over long term operating conditions, will not severely affect the ability of the material to perform. >>>
View the product on bergquistcompany.com The Bergquist Company
THERMAL PROTECTORS - MIGHTY MITE

THERMAL PROTECTORS - MIGHTY MITE
For over 40 years, Mighty Mites have served industry by providing maximum flexibility in design configuration. Mighty mites offer long life, reliable performance, and temperatures set to your specification. Features 100% factory tested. Tubular copper construction provides extra strength and is dust tight Impregnated Fiberglass insulation resists moisture absorption. Silver contact points ensure maximum electrical contact. Most models are UL approved. Mighty Mite Thermal Protectors are available in a variety of models to meet your specific product requirement: from 8 amps in Model 70-M to 50 amps in Model 325. Lead wires-generally #18 gauge-are pre-applied at the factor to your wire type and length requirements. >>>
View the product on thermtrol.com ThermTROL
ACTIVE THERMAL MANAGEMENT - COOL-STACK III™

ACTIVE THERMAL MANAGEMENT - COOL-STACK III™
A one rack-unit high cooler suitable for moderate heat loads. Heated air can be exhausted to the front or therear. Multi-speed operation; speed set by remote temperature switch. Extremely quiet.Features- Very low noise- Automatic speed selection- Control options: thermal switch, trigger, or contact closure- Multiple exhaust options; front and rear exhaust ports and tubing included- Requires only 1 rack space >>>
View the product on rotechsystem.com Rotech Systems
THERMAL MATERIALS - GAP PAD 3000S30

THERMAL MATERIALS - GAP PAD 3000S30
Gap Pad 3000S30 is a soft gap filling material rated at a thermal conductivity of 3 W/m-k. The material offers exceptional thermal performance at low pressures due to an all new 3 W/m-k filler package and low-modulus resin formulation. It is reinforced to enhance material handling, puncture, shear and tear resistance. It is well suited for high performance, low-stress applications that typically use fixed standoff or clip mounting. Gap Pad 3000S30 maintains a conformable yet elastic nature that allows for excellent interfacing and wet-out characteristics, even to surfaces with high roughness and/or topography.Gap Pad 3000S30 is offered with natural inherent tack on both sides of the material, eliminating the need for thermally-impeding adhesive layers. The material's natural inherent tack allows for stick-in-place characteristics durnig assembly. Gap Pad 3000S30 is supplied with protective liners on both sides. >>>
View the product on bergquistcompany.com The Bergquist Company
THERMAL CONTROLS - M SERIES REGULATING THERMOSTATS

THERMAL CONTROLS - M SERIES REGULATING THERMOSTATS
Thermtrol offers a truly unique snap-acting, high-precision thermostat using a sharp, semi-permanent snap spring with a flat non-distorting twin bimetal construction. This thermostat offers increased sensitivity and a narrow differential to maintain uniform temperature stability. The thermostat is housed in a low, thermal-resistant thermoplastic enabling it to react quickly to temperature variations and is offered in various mounting options. >>>
View the product on thermtrol.com ThermTROL
THERMAL MATERIALS - HI-FLOW 225U

THERMAL MATERIALS - HI-FLOW 225U
Thermal impedance: 0.07°C-in2/W (@25 psi)Hi-Flow coating will resist drippingThermally conductive 55°C phase change compoundAvailable in roll form with kiss-cut partsHi-Flow 225U is designed as a thermal interface material between a computer processor and a heat sink. The product consists of a thermally conductive 55°C phase change compound coated on a release liner and supplied on a carrier.Above its phase change temperature, Hi-Flow 225U wets out the thermal interface surfaces and flows to produce low thermal impedance. Hi-Flow 225U requires pressure of the assembly to cause flow. >>>
View the product on bergquistcompany.com The Bergquist Company


12Suivant >>Fin >
Go to page


  Search    
 
 
 
Search
See all of the sector's products : Manufacturing and processes