Thermal measuring devices: suppliers, wholesalers and manufacturers on Hellopro
Search   


Thermal measuring devices :

324 products
Select the category
Selection of 46 products among 324
ANVILLE SERIES 800 THERMAL VALIDATION INTERFACE

ANVILLE SERIES 800 THERMAL VALIDATION INTERFACE
The Anville Series 800 TVI range is designed for use with EaziVal SE and EaziVal Pharma software. Anville's thermal validation systems can be used wherever it is necessary to maintain a formal record to prove that the correct temperatures and pressures have been achieved during a critical process. Anville understand that equipment testing and validation are undertaken by busy engineering staff and have concentrated on making Eazival SE and EaziVal Pharma easy to setup and use. >>>
View the product on anvilleinstruments.co.uk Anville Instruments Ltd
ZR420 - WIRELESS THERMAL SENSOR - PS1488.2

ZR420 - WIRELESS THERMAL SENSOR - PS1488.2
ZR420 Wireless Thermal Sensor No external aerials Dual battery supply Full device status monitoring - power sources, head removal and device tamper Automatic sensitivity adjustment, alarm verification and self test Designed to provide heat detection on ZP3 systems, where the installation of hard wiring is not an option, the ZR420 wireless thermal sensor is a thermistor-controlled device, which responds to changes in its ambient temperature. The unit is controlled directly from the main fire detection panel, via a loop wired radio interface module. This arrangement allows both wireless and hardwired devices to be seamlessly located on the same loop wiring. The device provides a reliable response to fires in areas where environmental conditions may prohibit the use of smoke sensors. The sensitivity of each sensor is set by the main control panel and can be adjusted between four levels - from 58OC to 75OC, either manually or on a timed basis. At sensitivity level two the ZR420 fully meets the requirements of European Standard EN54 Part 5 (grade 1) and is approved by several international approval bodies. Installed as part of the ZP3 analogue addressable system, up to 127 devices can be connected to each of the control panel loops. Each wireless device, controlled through the ZR470 loop interface is assigned its own IDENT address, with which the main control panel communicates, providing the same system facilities as directly wired devices. Temperature levels are continuously sensed by the unit and transmitted to the radio loop module, which in turn relays the data to the main control panel. Four levels of sensitivity can be set and calibration and self-test are carried out automatically. Removal or replacement of an incorrect sensing device is identified by the system and details displayed at the main control panel. For ease of removal sensors plug into the ZR400 radio base by a simple twist and lock action. Bases are installed using a matching fixing plate. A site selectable option is provided to lock the sensor into its base. Once applied the unit can only be removed by means of a special tool. Specification Model No.: ZR420 Specification: EN54 Pt5 Approval: R&TTE to ETS300-220 Compatibility: All ZP3 analogue systems via ZR740 loop module. Performance: Grade 1 (at sensitivity level 2) Sensitivity settings: Level 1 58OC fixed temperature Level 2 58OC rate compensated Level 3 75OC rate of rise Level 4 75OC fixed temperature Mounting: Plugs into surface base Area Coverage: 100m2, subject to local codes Monitoring: Continuously self-checking Indication: Alarm LED (red) Operating voltage: 3.2 volts Power supply: In base (see PS1492) Addressing method: Unique address embedded in firmware Detection principle: Thermistor Environmental: Application: Indoor use EN60529 rating: IP32 Temp range: -10OC to +70OC Humidity range: 20% to 95% RH (non condensing) EMC: CE marked (EEC89/336) Construction: Material: Moulded ABS Dimensions: 106mm (Dia) x 52mm (H) (excluding base) Height from ceiling with base: ZR401 surface base - 82.7mm Colour: White Weight: 85g (without base) >>>
View the product on ziton.com GE Security
FTI-E THERMAL IMAGERS

FTI-E THERMAL IMAGERS
High resolution radiometric thermal image, giving detailed temperature information transmitted via a high speed digital connectionAccurate temperature measurement, enabling optimum process control from over 76,000 individual temperature measurementsSimple installation and ease of use, reduces installation cost and complexityDesigned for harsh industrial environments, ensuring ultimate measurement reliability and availability >>>
View the product on landinst.com/infrared/index.htm Land Instruments International
THERMAL IMAGER - FLUKE TI THERMOGRAPHY

THERMAL IMAGER - FLUKE TI THERMOGRAPHY
ThermoView Ti 10/25/20/TIR, 40FT-55FT he Fluke ThermoView Ti thermal imagers - affordable thtough to premium thermal cameras specifically designed for use in maintenance, with what maintenance professionals need to conduct thermographic inspections anytime, anywhere: * Thermal imager that measures temperature * Fast target scanning * Includes full-featured software for analysis and reporting * Low breakthrough price - from under £3000 to £15000 up. Our prices are the best available and we will consider matching any discount offered. >>>
View the product on radir.com/ RADIR THERMAL IMAGING SYSTEMS
ZR432 - WIRELESS COMBINATION SMOKE AND THERMAL SENSOR

ZR432 - WIRELESS COMBINATION SMOKE AND THERMAL SENSOR
ZR432 Wireless Combination Smoke and Thermal Sensor No external aerials Dual battery supply Full device status monitoring - power sources, head removal and device tamper Senses both smoke and heat Designed to provide the earliest response to a wide range of fire types, in locations where hard wiring is not an option, the ZR432 wireless sensor combines optical smoke sensing and thermal monitoring to provide an accurate warning of fire. Individual monitoring of each element, measures actual smoke levels, in addition to temperature rates of rise. When installed using the ZR401 base the sensors operation can be selected as either smoke or heat. The ZR402 base enables the unit to operate as a multi sensor utilizing both smoke and heat channels. Smoke sensing can be isolated for areas where ambient smoke may exist at certain times of the day, or used on a day night basis in premises where heat only is required whilst the building is occupied. Temperature response meets the requirements of European Standard EN54 Part 5. (Settable to grade 1 or grade 3), with smoke sensitivity complying with EN54 Part 7. The sensor is approved by several international approval bodies. The unit is controlled directly from the main control panel, via a loop wired radio interface module. Up to 127 devices can be connected to each of the control panel loops, allowing both wireless and hardwired devices to be seamlessly located and controlled from the same wiring loop. Each wireless device, controlled through the ZR470 radio interface unit, is assigned its own IDENT address, with which the main control panel communicates, providing the same system facilities as directly wired devices. Temperature and smoke sensitivity can be set by selection switches located on the base plate of the unit, calibration and self test are carried out automatically. Removal or replacement of an incorrect sensing device is identified by the system and details displayed at the main control panel. Sophisticated auto contamination adjustment compensates for any long-term drift in performance, caused by dirt entering the sensing chamber. For ease of removal sensors plug into the ZR400 radio base by a simple twist and lock action. Bases are installed using a matching fixing plate. Specification Model No.: ZR432 Bases: ZR401 - selectable heat or smoke sensing ZR402 - multi-sensing operation Specification: EN54 Pt5 and Pt7 Description: Wireless smoke/heat sensor Approval: R&TTE to EST300-200 Operating frequency: VHF 173.245 MHz Compatibility: All ZP3 analogue systems via ZR740 loop module Mounting: Plugs into surface base Area Coverage: Smoke element: 100m2, subject to local codes Thermal element: 50m2, subject to local codes Monitoring: Continuously self-checking Detection principle Smoke: photo electric light scatter Thermal: thermistor Addressing method: Unique address embedded in firmware Indication: Alarm LED (red) Operating voltage: 3.2 Vdc Power supply: in base (see publication PS1492) Environmental: Application: Indoor use EN60529 rating: IP32 Temp range: -10OC to +75OC Humidity range: 20% to 95% RH (non condensing) EMC: CE marked (EEC89/336) Construction: Material: Moulded ABS Dimensions: 106mm (dia) x 58mm (h) (excluding base) Height from ceiling with base: ZR401 surface base - 88.7mm Colour: White Weight: 105g (excluding base) >>>
View the product on ziton.com GE Security
9500P DIGITAL PROGRAMMABLE PROCESS CONTROLLER

9500P DIGITAL PROGRAMMABLE PROCESS CONTROLLER
Features of the 9500P programmable process controller. • Full PID auto-tuning process controller • Total of 3 outputs, from 4-20mA, 0-5v, 0-10v, SSR drive, relay • Input options: Thermocouple 2 or 3 wire PT100 0-50mV, 0-5V, 0-10V, 0-20mA, 4-20mA • Alarms with 5 options • Heat-cool operation • Programmer operation • Sleeve mounting for easy maintenance • IP66 protection from front panel • CE, UL & CSA approvals • 3-year warranty • Monitoring and configuration software option • RS232/485 options, Modbus RTU protocol Programmer Features • Up to 31 programs (profiles) • Up to 126 segments • Unlimited use of event outputs via the 2nd and 3rd outputs • Copy/paste/edit/delete functions to simplify program building • Call another program as a sub-program segment • Up to 999 program loop cycles, or continuous loop cycling • Hold back function to ensure the next segment is not started until the last segment reaches set-point • 3 power fail recovery options, (hold, continue or reset) • Front Panel Interrogation of the program position • Memory usage indication during programming Front panel 'release from hold' function to run the program. Specification - 9500P Thermocouple types: 9 types: B,E,J,K,L,N,R,S,T Standards: IPTS/68/ DIN 43710 CJC rejection: 20:1 (0.05°/°C) typical External resistance: 100 ohms maximum Other input options: 0 to 50mV +/-0.1% 4-20mA +/-0.1% 0-5V +/-0.1% 0-10V +/-0.1% Applicable to all inputs (SM = sensor maximum) Calibration accuracy: +/- 0.25% SM +/-1°C Sampling frequency: input 10Hz, CJC 2 sec. Common mode rejection: Negligible effect up to 140db, 240V, 50-60Hz Series mode rejection: 60db, 50-60Hz Temperature coefficient: 50ppm/°C SM typical Reference conditions: 22°C +/- 2°C, rated voltage after 15 minutes settling time. Output devices (check configuration) SSd1 and SSd2 solid state relay driver: to switch a remote SSR 6VDC (nominal) 20mA non-isolated Miniature power relay: form A/SPST contacts (AgCdO) rLY1, rLY2, rLT3: 2A/250VAC resistive load Analogue output: 4-20mA 500 ohms max’ +/- 0.1% fs typical 0-5Vdc 10mA (500 ohms min’) +/- 0.1% fs typical 0-10Vdc 10mA (1K ohms min’) +/- 0.1% fs typical General: Displays: Upper, 4 digits, high brightness green LED 10.4mm (0.4") high. Lower, 4 digits, high brightness orange LED 9mm (0.35") high. Digital range –199 to 9999 Hi-res mode –199 to 999.9 LED output indicators – flashing SP1 square, green; SP2/SP3 round, red. Keypad: 3 elastomeric buttons. Power Supply: 100-240V AC, 50-60 Hz , (typ' 5.0 VA) >>>
View the product on cal-controls.co.uk CAL Controls
0-10% SCALE CUTTING OIL REFRACTOMETER

0-10% SCALE CUTTING OIL REFRACTOMETER
Model: REF-101C Shipping Weight: 0.3Kg REF-101C visual hand held refractometer with Percent scale, range 0 to 10%, resolution 0.1%. For very low concentration samples where high precision is required. It is especially for degradation studies of cutting oils. Rugged, durable construction - made from corrosion resistant brass. High contrast demarcation line for easy, accurate readings. Easily adjusted zero line by means of readily accessible screw. Size 27 x 40 x 210 mm >>>
View the product on refractometers.com Index Instruments Ltd
BASE METAL THERMOCOUPLE ASSEMBLY WITH CERAMIC SHEATH - BMC

BASE METAL THERMOCOUPLE ASSEMBLY WITH CERAMIC SHEATH - BMC
Type Designation: BMC Temperature Range: -200 to 1700 ° C depending on sensor type Common Sensor Types: K, J, N, T, E Common Size : Ø 6.0, 8.0, 10.0, 12.0, 13.0, 15.0, 17.0, 20.0, 25.0, 28.0, 50.0mm Common Element Diameters: Ø 0.15mm to 0.5mm Shank: Plated MS, stainless steel , chrome iron, alloy 600 Heads: ALA, KNE (IP65), HR AL BL (flip top), many others Application Notes: Range of thermocouple types to choose from Will withstand tough industrial use Special Options: Special materials available on request Lining sheaths for porous materials available Shanks fitted for head assembly Adjustable or welded flange on shank Pressure tight design possible >>>
View the product on peaksensors.co.uk Peak Sensors Ltd
3 PHASE ELECTRICITY METER

3 PHASE ELECTRICITY METER
Information The OFGEM approved three-phase electronic meters are designed for measuring kWh in three-phase four-wire networks. Available as CT operated or 120A direct connected. Features Fast and easy installation procedure, indicators show correct connection Smaller dimensions for overall cost reduction of the meter site Multi-phasing connection (all in one: single and poly-phase meter) Universal current terminals for all type of wires Indication of operational status Optical communication port for semi-automatic meter reading >>>
View the product on tmac-tech.com/ t-mac Technologies Limited
OIL TCU-TT-240

OIL TCU-TT-240
Temperature Control Unit Compact unit for use with oil up to 200ºC. Closed hot oil circuit with integral cold oil receiver in large expansion tank - long oil life due to low heater loads/high flow rate Self-optimising microprocessor controller with digital display of set and actual temperature Connection for optional external thermocouple Leakstopper – operation in pressure or vacuum mode, to allow continuous production despite leakage from mould or connections Automatic mould drain Automatic temperature control - audible alarm sounds when unit deviates outside 5ºC preset (adjustable). Heating switchable in stages Limescale-free heat exchanger No oil cracking No cooling-down required before switching off Safety devices: - level control provides auto dry run protection - electronic and mechanical safety thermostats - audible alarm in case of failure >>>
View the product on tool-temp.net Tool-Temp UK
1/16 DIN DUAL DISPLAY PID TEMPERATURE CONTROLLER

1/16 DIN DUAL DISPLAY PID TEMPERATURE CONTROLLER
This powerful and versatile yet low cost PID controller has dual 4 digit display of process and set values and can be ranged by the user for a variety of inputs and alarms. This auto tuning controller also features continuous self tuning which in the majority of applications sets the controller up for optimum performance. - PID Auto tuning or On/Off can be selected - 1/16 DIN (48x48x100mm deep) - 4 digit dual LED display - Accuracy: Typically better than ±0.3% of FSV - 100-240V AC as standard. Contact us if you require 24V AC or 24V DC versions - Customer rangeable for Type K J T N E R S and B thermocouple or Pt100 inputs - Temperature (process or deviation) or Loop break alarms can be configured - Relay or Solid State Relay drive (SSR) or 4-20mA output versions - Non volatile memory - 3 year warranty >>>
View the product on tc.co.uk TC Ltd
THERMOCOUPLES TC GP PFL

THERMOCOUPLES TC GP PFL
The GP FL Series of Thermocouples comprises of a range of high quality low cost general purpose probes. Sheaths are manufactured in 316 stainless steel in a choice of sizes, connected to various types of flying leads. Having a maximum tip temperature of 400°C they are suitable for many applications. A wide variety of installation fittings is available along with a choice of wire terminations. The sheaths are available in 3mm, 4.5mm or 6mm diameters. >>>
View the product on terwin.com Terwin Instruments
NC (NON-CONTACT) IR SENSORS - F-TYPE

NC (NON-CONTACT) IR SENSORS - F-TYPE
NC SENSOR - Our Non Contact (NC) sensor is a new concept in measuring infrared heat for temperature control. Utilising our own micro thermistor technology, we have developed a sensor which can be easily installed, is self-compensating and can withstand more aggressive environments than other conventional infra-red sensors. It is ideally suited for controlling the temperature of fuser rollers in laser printers and copiers. >>>
View the product on atcsemitec.co.uk ATC Semitec Ltd
PNEUMATIC ACTUATORS HIGH TEMPERATURE

PNEUMATIC ACTUATORS HIGH TEMPERATURE
To pilot ball, butterfly and plug valves in high temperature ambients. ~ Designed to automatize fire security systems. ~ Constructed with metallic materials, inox and protected against corrosion by cataphoresis and special teflon. ~ Can be piloted with air and non agresive fluids, up to 8 bar (up to 15, on demand). ~ Models in Double Acting and Spring Return, with torques from 25 Nm. up to 2.000 Nm. at 6 bar. ~ Norms of construction: ISO 5.211, DIN 3.337, VDE 3.845, NAMUR. ~ Can withstand temperatures up to 265ºC. Certificate from the L.G.A.I. (Laboratori General d'Assaigs) >>>
View the product on gibsonexports.ltd.uk Gibson Exports Limited
DIGITAL THERMOSTAT - JUMO ETRON T

DIGITAL THERMOSTAT - JUMO ETRON T
JUMO eTRON T Digital thermostat with LC display for mounting on a 35mm DIN rail (70.1050)The JUMO eTRON T is a compact digital thermostat in 90mm x 22.5mm format for simple temperature control (heating or cooling). The measurement input permits the connection of resistance thermometers or thermocouples, or standard current or voltage signals. The measured value is shown on a 3-digit LC display. The switching status of the relay K1 is indicated by an LED.The instrument is operated from 3 keys on the front panel. The electrical connection is made via screw terminals.A setup program and a PC interface are available as accessories, for easy configuration and parameterization from a PC. >>>
View the product on jumo.co.uk JUMO Instrument Company
POINTSCAN® PRESSUREX® MEASUREMENT SYSTEM

POINTSCAN® PRESSUREX® MEASUREMENT SYSTEM
This easy-to-use tool prompts the user to enter temperature, humidity, time of exposure and film type, it then quickly displays the pressure reading in either Metric or English units of measurement. PointScan® is a durable device with multiple aperture dimensions which ensure accurate scanning of your surface pressure indicating film and it has a quick recalibration protocol that ensures high repeatability. >>>
View the product on sensorprod.com Sensor Products Inc
INFRA RED TEMPERATURE OPTRIS CS

INFRA RED TEMPERATURE OPTRIS CS
OPTRIS CS - Low cost infra red thermometer -20C to + 350C Size: M12x1, 87 mm long, stainless steel housing Temperature range: -20 to 350°C. Usable up to 75°C ambient temperature without cooling Scalable analog output: 0 - 10 V or 0 - 5 V Short circuit and polarity reversal protection Optional USB programming interface and software Wide power range: 5 - 7, 12 - 28 V DC Rugged coated silicon optics Integrated Electronics with LED alarm indication and smart sighting support Adjustable signal processing >>>
View the product on amsolve.co.uk Advanced Maintenance Solutions Ltd
ANVILLE SERIES 425 DATA LOGGER

ANVILLE SERIES 425 DATA LOGGER
The Anville series 425 system has 16 inputs for fifteen type T thermocouples and one pressure sensor input. Anville systems use Coto reed relay switching for thermocouple and pressure inputs. Reed relays have many advantages over semiconductor switching including 250VDC isolation between inputs, 400VDC isolation to ground, no thermoelectric EMF generation, no resistive offsets, long life and total reliability. Conversion to engineering units (°C/°F) is carried out by the microprocessor in the Anville system with data communicated to the computer in the correct engineering units enabling the system to have a traceable calibration certificate. An internal power supply provides the excitation voltage for the pressure transducer. >>>
View the product on anvilleinstruments.co.uk Anville Instruments Ltd
LOOP POWERED SENSOR 4-20 MA PC420 LPS

LOOP POWERED SENSOR 4-20 MA PC420 LPS
PC420 LPS™, top exit. PC420 vibration Sensors provide a 4-20 mA output signal proportional to an overall vibration level. This type of output is commonly accepted by process control systems such as Programmable Logic Controllers (PLC) or Distributed Control Systems (DCS). By connecting into process control systems, the user is able to monitor machinery condition without the investment and learning curve commonly associated with traditional vibration monitoring systems with data collection boxes and custom software. >>>
View the product on wilcoxon.com Wilcoxon Research
MOISTURE CONTROL

MOISTURE CONTROL
High humidity levels and low winter temperatures can be rough on your business, causing condensation and corrosion to your critical operations. You can improve your productivity and maintain a controlled environment with dehumidification solutions from Aggreko. Some humidity control applications available include: Developing stable environments for exposed metal to prevent corrosion Reducing drying times at construction sites for concrete, insulation, and fireproofing Blanketing equipment to protect from highly humid air Drying out water-damaged buildings, eliminating the need to replace and reconstruct. >>>
View the product on aggreko.com Aggreko UK Ltd
PORTABLE ANALYSERS - MODEL DSP FCI

PORTABLE ANALYSERS - MODEL DSP FCI
Portable Digital Hygrometer Sample flow control for inlet pressure up to 20 barg Various Ranges: Overall Range -110ºC to +20ºC Dewpoint Selectable Engineering Units in ºC, ºF, ppb(v), ppm(v),ppm(w), g/m & lb/MMSCF Desiccant Dry-Down Chamber for Rapid Measurements In excess of 250 Hours of Continuous Operation Self-Diagnostics on Start-up Quick Connect SS Coupling Portable - Fully Self Contained Takes ordinary 'C' type batteries This is a fully self-contained digital portable hygrometer which will deliver the most dependable moisture measurements in industrial and laboratory applications. >>>
View the product on amsystems.co.uk Alpha Moisture Systems
INDUSTRIAL DOOR SENSOR

INDUSTRIAL DOOR SENSOR
The door sensor is designed to be used as part of a System5 in conjuction with a SCOUTPLUS and records the total number of minutes that the door has been opened during a given period. Available in Standard and Industrial versions Smallest time interval recorded: 5 seconds Smallest time interval displayed: 1 minute Data presentation: x minutes open during the corresponding log period, e.g. 3 minutes total open time in 10 minutes Short open times (less than 1 minute) rounded up to 1 minute Short closed times (less than 1 minute) rounded up to 1 minute Successive short openings during the same minute: recorded as one minute Dimensions of standard magnetic actuator : 80 x 80 x 20mm (smaller mechanical actuators also available for domestic style doors) Cable material: PVC screened Standard cable length: 1500mm (other lengths available to order) Dust / Waterproofing: IP67 when mated with ScoutPlus >>>
View the product on icespy.com Abacus IceSpy


12Suivant >>Fin >
Go to page


  Search    
 
 
 
Search
See all of the sector's products : Measuring devices, analysis and sensors