Pressure sensors: suppliers, wholesalers and manufacturers on Hellopro
Search   


Pressure sensors :

361 products
Select the category
Selection of 120 products among 361
MEDICAL - PROFESSIONAL BP SENSOR - UM-101 NEW

MEDICAL - PROFESSIONAL BP SENSOR - UM-101 NEW
The UM-101 mercury-free sphygmomanometer opens up a completely new era of professional blood pressure measurement. In 1905, Dr. Nikolai S. Korotkov introduced his theory of blood pressure measurement using the Riva-Rocci mercury monitor. Since then, blood pressure measurement using the mercury column has been reigned as the gold standard of blood pressure measurement, and his method known as the "Korotkov method" or "auscultatory method" is used for daily blood pressure monitoring by healthcare professionals worldwide. >>>
View the product on andinstruments.co.uk A & D Instruments Ltd
AMBULATORY BLOOD PRESSURE MONITORS - TM-2430

AMBULATORY BLOOD PRESSURE MONITORS - TM-2430
The TM-2430 is a compact & lightweight ambulatory blood pressure monitor, which incorporates our latest technology gained from over 20 years experience in the manufacturing of ambulatory BPMs. This monitor was validated in accordance with BHS protocol and its accuracy was proven to be A/A. Weighing only 215 grams, and the size of a cigarette pack, the portable TM-2430 can be easily taken anywhere with a patient. >>>
View the product on aandd-eu.net A+D Medical
PRESSURE - PTX300 HIGH PRESSURE TRANSMITTERS

PRESSURE - PTX300 HIGH PRESSURE TRANSMITTERS
The PTX300 is a low cost compact high pressure transmitter which features a sputtered thin film sensor to provide consistent high levels of performance and stability. The M12 electrical connection provides IP67 protection and the compact 17-4 PH stainless steel construction makes the PTX300 series ideal for installations where space is at a premium. Ranges 0 to 2200 Bar 0.25% Accuracy Operating Temperature Range –40 to +125 degC Less than 35mm long >>>
View the product on accessinstrumentation.com Access Instrumentation Ltd
LOW PRESSURE SAMPLE SYSTEM - MODEL SSI

LOW PRESSURE SAMPLE SYSTEM - MODEL SSI
Low Pressure Sample System - Maximum inlet pressure up to 28 barg, with sensor operating at atmospheric pressure. This system is designed for gas or general compressed air sampling for maximum inlet pressure of 28 barg, with the moisture sensor operating at atmospheric pressure. The system provides for all necessary pressure and flow control and includes sample filtration to protect against particulate contamination. Auxiliary inlet connection is provided for a second sample stream or for injection of a calibration gas. An outlet connection is also included to allow sample recovery or disposal.Sample inlet pressure up to 28 barg Sensor operating at atmospheric pressure >>>
View the product on amsystems.co.uk Alpha Moisture Systems
DIFFERENTIAL PRESSURE SENSORS MODEL5100

DIFFERENTIAL PRESSURE SENSORS MODEL5100
This product has been Approved to CE standard EN61326. The Model 5100 is a competitively priced, high quality, differential Pressure Sensor intended for use in the measurement of non-corrosive gases. This series is suitable for automotive diagnostics tools, industrial applications, pneumatics, and data loggers. Model 5100 transducers have been designed specifically for applications with demanding price and performance requirements. Model 5100 transducers offer high level outputs, and low thermal errors. The housing in constructed from aluminum and stainless steel. Additionally, measurements are available in differential pressure covering ranges up to 3 PSI (20 PSI Line Pressure Max). Model 5100 users can expect long life and high performance, making this model ideal for applications needing high accuracy, excellent long-term stability, and trouble free operation. Each unit is backed by AST's one-year warranty. FEATURES· Compact design; No oil filled cavities eliminates the chances of process contamination; High level of EMI/RFI protection - 100V/m; All stainless steel construction; High shock and vibration tolerance. APPLICATIONS · Wide range of applications such as boiler controls, HVAC, filtration, pipeline gas instrumentation, and data loggers. WARRANTY · Workmanship - AST, Inc. pressure transmitters have a limited one-year warranty to the original purchaser. AST, Inc. will replace or repair, free of charge, any defective transmitter. This warranty does not apply to any units that have been modified; misused, neglected or installed where the application exceeds published ratings. · Installation/Applications - The purchaser is responsible for media compatibility, functional adequacy, and correct installation of the transmitter. The sensor must be protected from mechanical damage when properly installed. >>>
View the product on astsensors.com American Sensor Technologies
COLLISION SENSOR - QS-100

COLLISION SENSOR - QS-100
The QS-100 is a dynamically variable collision sensor that operates on an air pressure system. A regulated air supply provides positive, variable pressure to hold the collision sensor rigid during normal operation. At impact, the air chamber seal is opened, immediately signaling the system controller. Key Benefits Dynamically variable trip points Permanent repeatability Use on linear actuators, robots, pick-and-place machines Detects angular, rotational and compressive forces >>>
View the product on arobotics.com Applied Robotics
F4 PRECISION PRESSURE GAUGE CALIBRATOR - ISSUE 12

F4 PRECISION PRESSURE GAUGE CALIBRATOR - ISSUE 12
F4 Precision Pressure Gauge Calibrator - Issue 12 This instrument allows pressure gauges to be accurately calibrated within the range 1 - 300 bar. ORDERING SPECIFICATION • Portable, self-contained dead weight precision pressure gauge calibrator. • Calibrates gauges 1-300 bar range to ±0.015% of reading. • Supplied complete with laboratory calibration certificate • Includes carrying case and weights. • Minimum standard weight increment is 0.05bar. Test Capabilities > Calibration of pressure gauges by dead weight method to an accuracy better than 0.015% of reading > Dual pistons allow calibration over a wide range of pressures Description Deadweight testers are the basic primary standard used both world-wide for the accurate calibration of pressure gauges, pressure transducers etc. The equipment is self-contained and portable, so it may be used in lecture theatre demonstrations or as a master calibrator for the laboratory. The instrument combines a low and high pressure range provided by two pistons of different effective area. Calibration is accurate to within ±0.015% of reading. A laboratory calibration certificate is supplied for each piston together with a traceable certificate of overall accuracy. The pressure in the system is produced by means of a capstan operated hydraulic ram, balanced by a dead weight acting upon a piston of known area. Oil is used as the hydraulic fluid. The pressure developed is applied to the gauge that is to be calibrated. A spirit level and adjustable feet are provided to enable the operator to level the instrument. A flotation indicator mounted on the top plate removes the guess work when floating the piston. The instrument is supplied complete with necessary weights and a fitted carrying case. 1/8", 1/4", 3/8", 1/2" BSP and NPT female adaptors are included together with spare seals and a quantity of oil. (Gauge not supplied). Shipping specification Volume: 0.5m3 Gross weight: 70kg Overall dimensions Length: 430mm Width: 280mm Depth: 220mm >>>
View the product on armfield.co.uk Armfield Limited
PRESSURE SWITCHES - TYPE A-SERIES

PRESSURE SWITCHES - TYPE A-SERIES
Miniature Pressure Switches, Watertight Brass Body, Type A-Series Wide variety of electrical connections including spade, screw, and DIN Rugged brass body sealed for environmental protection Precision snap-acting switch element Choice of field-adjustable or factory-adjusted to setpoint requirements UL and CSA listed The Ashcroft® A-Series pressure switches are designed for tough industrial and OEM applications requiring a durable, high-quality miniature switch. Ideal for pressure alarm, shutdown, or control on heavy vehicles, machine tools, electronic equipment, engines, compressors, and wherever size is a consideration or equipment is being downsized. >>>
View the product on ashcroft.com ASHCROFT Groupe - DRESSER FLOW CONTROL
PRESSURE INSTRUMENTS STAINLESS STEEL

PRESSURE INSTRUMENTS STAINLESS STEEL
The stainless steel pressure gauge is a product of high quality. The stainless steel pressure systems are all provided with seamless drawn tub which reduces the chance of tube rupture. All gauges have the connection welded into the case and is produced according to the international standard EN837 and the PED. They can be supplied with 3.1, Nace and calibration certificates and can also be equipped with ATEX declaration. >>>
View the product on badotherm.co.uk Badotherm UK Ltd
DIAPHRAGM PRESSURE SWITCHES - D2X

DIAPHRAGM PRESSURE SWITCHES - D2X
Features Metal Diaphragm Pressure Switch, 2 switching contacts, Adjustable swirch contact, for vacuum and overpressure Applications Petro-chemical industry, Process industry Technical data Adjustment ranges -0,006 bar…-1,00 bar up to 0,012 bar...10,3 bar Measuring element Stainless steel diaphragm Number of contacts 2 Max. switch frequency / min 20 Repeatability in % + - 1 Vibration tolerance Vibration tolerance satisfactory Process connection (without adaptor) 1/4" NPT female, 1/2" NPT female, stainless steel Electrical connection Terminal clip Max. electrical rating acc to CENELEC Housing Aluminium, pressure proof enclosed Protection class IP65 Options Gold-plated contacts, hermeticlly sealed contacts Approvals Exi and Exd >>>
View the product on barksdale.co.uk Barksdale Control Products
INDUSTRIAL PRESSURE TRANSMITTER FOR VERY LOW PRESSURE - DMP 343

INDUSTRIAL PRESSURE TRANSMITTER FOR VERY LOW PRESSURE - DMP 343
Piezoresistive silicon sensor ? especially for gaseous, non-aggressive media ? accuracy: 0.175 % FSO BFSL (0.350 % FSO IEC 60770) ? nominal pressure ranges from 0 ... 10 mbar up to 0 ... 1000 mbar The pressure transmitter DMP 343 is designed for measurement of very low gauge pressure starting at 10 mbar and for vacuum applications (-1 … 0 bar). Permissible media are gases, pressurized air and non-aggressive liquids of low viscosity. Basic element of the pressure transmitter DMP 343 is the silicon sensor DSP 201. The ultimate sensor element is mounted on a ceramic substrate, the media coupling occurs on the backside of the piezoresistive silicon sensor. The DMP 343 features excellent thermal behaviour and outstanding long termstability. A variety of standard output signals as well as mechanical and electrical connections make the DMP 343 covering a wide field of applications. Applications: ? process control ? pneumatic control systems ? heating and air conditioning ? filter technology ? computer peripherals and systems >>>
View the product on bdsensors.com BD SENSORS
HIGH PRESSURE TRANSDUCER MODEL 8221

HIGH PRESSURE TRANSDUCER MODEL 8221
Measuring ranges from 0 ... 1000 bar to 0 ... 5000 bar Accuracy < 0.5 % Suitable for liquid and gaseous media Can be used for dynamic and static measurement Made of stainless steel Standardization sensivity to 2.0 mV/V Application This transducer for high pressure is designed for universal use. The features of this unit are good accuracy, high reliability, ruggedness and excellent long term stability. It works with a metal-coated strain gage sensor element connected as full bridge and providing a standardized output signal The unit is suitable for dynamic and static measurement on liquid and gaseous media. The range of application for this pressure tansducer are laboratories, production, industrial processing, automatic operation, marine engineering or aviation industry. Especially to be mentioned is the proven and mature technology of this sensor resulting in a simple and user-friendly operation. Description The unit is built from rugged electronic components and ultrasonic tested material. This helps to avoid mechanical faults and enhances the reliability and versatility of the product in industrial use. The actual sensitive element is produced from one piece of solid steel. This enforces the operating reliability because the media does not touch welding seams. The connection between sensitive element and pressure port is done by electron beam welding to save the good physical property of the stainless steel. To ensure the versatility of the transmitter without recalibration of the following electronics, the output signal is standardized to 2.0 mV/V. Internal amplifiers for 4 ... 20 mA, 0 ... 5 V or 0 ... 10 V are available. The output ist protected against polarity reversal and short circuits. For a simple calibration or to test the following electronics, the high pressure transducer is fitted with an internal shunt resistor. >>>
View the product on burster.de burster
DIFFERENTIAL PRESSURE TRANSMITTERS - FCX-CII

DIFFERENTIAL PRESSURE TRANSMITTERS - FCX-CII
High reliability micro-capacitance silicon cells Static Pressure to 140 Bar on dp ranges Accuracy, +/-0.1% of calibrated span Exceptional resistance to harsh environments Hart® 5.2 multi-drop communication Versatile indicator with 5-digit display Field repair possible with common spare parts Built-in loop calibration facility Large installed base The Fuji Electric FCX-CII is a high performance low cost differential pressure transmitter. This is achieved by offering only stainless steel wetted parts and mid-range measuring cells. For high/low pressure ranges, or exotic materials, select the FCX-AII. The Fuji Electric FCX series of differential pressure transmitters use a silicon micro-capacitance cell proven on thousands of difficult applications. They are installed in harsh environments on oil pipelines, power stations, gas compressor stations, water treatment plants and steel plants. They have European, American, Russian and Chinese approvals. Field repair is possible using only one amplifier for all pressure transmitter types. >>>
View the product on coulton.com Coulton Instrumentation Ltd
M1 PRESSURE GAUGE

M1 PRESSURE GAUGE
Crystal Engineering developed a new product that directly competes with mechanical gauges. M1’s are rated in percent of reading - like deadweight testers - but unlike deadweight testers, they're not affected by ambient temperature (or local gravity). M1's are fully temperature compensated, so the accuracy is the same over the entire operating temperature range, and they can be used to measure vacuum. Because the rating is "of reading" - one M1 can often replace two or more ordinary gauges! The M1 digital pressure gauge has 0.2% of reading accuracy. >>>
View the product on crystalengineering.net Crystal Engineering
SMART 2HT PRESSURE TRANSMITTER

SMART 2HT PRESSURE TRANSMITTER
FUNCTIONAL SPECIFICATIONS Service :- Liquid, Gas or Vapour Ranges :- 0 ~ 1 to 0 ~ 1000 Bar ( 0 ~ 16 to 0 ~ 16,000 psi ) Sensor Limits:- 2 * URL Overpressure Stainless Steels except range GA, 0 to 1000 bar = 1.5 * URL 1.5 * URL Overpressure Monel & Hastelloy Output :- 4 to 20 mA DC 2 Wire System with digital AC signal superimposed on to it, using the HART protocol. Power Supply :- 9 to 55 Volts DC (Subject to 28 V maximum on Intrinsically Safe installations) Load Limits :- Dependent upon installation and PSU, See chart in Electrical Installation Hazardous Area Certifications :- See Certified Products Zero Elevation & Suppression:- Can be set anywhere within the sensor limits as long as the span is greater or equal to the minimum span, and URV does not exceed URL Normal or Reverse action :- Set by reversing the upper and lower range values. See Zero, Span and Rangeability Temperature Limits:- Operating :- -40 to +85 Degrees C Storage :- -50 to +110 Degrees C Display :- -30 to +80 Degrees C Failure Mode Alarms:- High or Low (Analogue) for a major transmitter malfunction. Humidity Limits :- 0 to 100% RH Turn-on Time :- Less than 6 Seconds, This includes full self diagnostics Volumetric Displacement :- < 1 microlitre Damping :- 0 to 39 Seconds, in addition to the sensor response time. PERFORMANCE SPECIFICATIONS Accuracy For spans of 1 : 1 to 10 : 1 +/- 0.1 % of SPAN, Including Linearity, Hysteresis and Repeatability For spans below 10 : 1 +/-0.15 % of SPAN Stability Typically less than 0.15 % URL per annum Temperature Effect Total effect +/- 0.10 % at Max. Span over ambient range Overrange Effect Zero shift, 0.2 % of URL Power Up Less than 6 seconds, including Diagnostics, Display and Memory tests Vibration Effect 5 g Peak sinusoidal at 5 Hz to 200 Hz without deleterious effect Power Supply Effect >>>
View the product on delta-controls.com Delta Controls Ltd
PRESSURE DATALOGGER - PLOG523

PRESSURE DATALOGGER - PLOG523
The P-Log523 measures and records simultaneously pressure and temperature in gases. On request it is also availabe for aquatic media. It is available in several different ranges form 100 to 35.000 kPa. Depending on the type of sensor applied the logger can either log gauge or absolute pressure. Temperature is not only recorded but is also used to accurately compensate for any temperature effects. Compact design The rugged enclosure from stainless steel houses both the sensors, the battery and the storing electronic. Having very small dimensions of Æ 25mm and length 215mm the P-LOG523 is IP67 protected and can be supplied with a couple of threads for process integration. At time of order it can be selected between 1/4" BSP, 1/8" NPT, 1/4" NPT and 7/16 UNF. Unattended for long measuring periods Up to one million readings can be recorded with a 16 bit resolution and the non volatile flash memory ensures that the readings are safe even if the battery fails. Because of its low power consumption the logger can work for up to 6 years with one battery, which can easily be exchanged by the user himself. The Software InfraLog for Windows gives you complete control over the P-Log523, including Setup, Download and graphing. >>>
View the product on driesen-kern.de Driesen+Kern
PTX 120/WL WET/WET DIFFERENTIAL PRESSURE TRANSMITTER

PTX 120/WL WET/WET DIFFERENTIAL PRESSURE TRANSMITTER
PTX 120/WL Wet/wet differential pressure transmitter The PTX 120/WL is a wet/wet differential pressure transmitter accepting a wide variety of pressure media on each port. Product Description The positive (high pressure) port is a fully welded 316 stainless steel assembly, the negative (low pressure) port contains stainless steel, silicon, glass, epoxy, aluminum and a silicon ‘o’ ring seal. Service Types Calibration In-House On-Site Evaluation Features & Benefits Ranges 2.5 to 500 psid ± 0.1% FS BSL Encapsulated electronics Zero and span trim controls Intrinsically safe as standard ±1.5% total error band -20°F to +80°C Output 2 wire, 4-20mA >>>
View the product on druck.com Druck Ltd
SENSOR ACCESSORIES 200100

SENSOR ACCESSORIES 200100
1/2-20 UNF Pressure Sensor Mounting Hole Cleaning Kit The Dynisco cleaning kit was designed for checking mounting hole dimensions and removing excess plastic from the mounting holes prior to installing melt pressure and temperature sensors. Installation of transducers into improperly machined, cleaned or improperly sized holes is the number one cause of damage to melt pressure sensors. This kit will allow a user to clean the 0.312" tip diameter hole, the 45 degree seating surface, and the 0.451" hole. The kit includes a gauge plug which is used to verify that the hole has been correctly machined and cleaned. M10 and M18 kits are also available. Important: The cleaning tool must be used when the polymer is in a semi-molten state. Care must be taken not to exceed a torque rating of 100 inch - pounds during scraping so as not to damage the cutting edges of the tool. These cutting edges are manufactured from hardened tool steel and will not wear if reasonable care is exercised. It is strongly recommended that a high temperature lubricant be applied to the tap and the threads of the guide sleeve and gauge plug to prevent seizing. Sensor Accessories 200100 1/2-20 UNF Pressure Sensor Mounting Hole Cleaning Kit The Dynisco cleaning kit was designed for checking mounting hole dimensions and removing excess plastic from the mounting holes prior to installing melt pressure and temperature sensors. Installation of transducers into improperly machined, cleaned or improperly sized holes is the number one cause of damage to melt pressure sensors. This kit will allow a user to clean the 0.312" tip diameter hole, the 45 degree seating surface, and the 0.451" hole. The kit includes a gauge plug which is used to verify that the hole has been correctly machined and cleaned. M10 and M18 kits are also available. Important: The cleaning tool must be used when the polymer is in a semi-molten state. Care must be taken not to exceed a torque rating of 100 inch - pounds during scraping so as not to damage the cutting edges of the tool. These cutting edges are manufactured from hardened tool steel and will not wear if reasonable care is exercised. It is strongly recommended that a high temperature lubricant be applied to the tap and the threads of the guide sleeve and gauge plug to prevent seizing. Features: Cleaning drill - P/N 200904 Cleaning drill guide - P/N 200906 Handle - P/N 200907 Gauge plug - P/N 200908 Bottoming tap - P/N 200905 Allen hex wrench - P/N 200909 Dykem blue - P/N 200910 >>>
View the product on dynisco.com Dynisco (UK) Ltd
PRESSURE TRANSMITTER

PRESSURE TRANSMITTER
The Model PT combines micro-machined silicon diaphragms with fully welded stainless steel pressure ports to provide a highly accurate, stable pressure transmitter. It is constructed with the materials and environmental protection required for industrial applications. The silicon sensors incorporate developments derived from aerospace applications. These developments are used to decrease output noise, non-linearity, and hysteresis and to improve long-term stability. A detachable industrial electrical connector provides access to independent zero and span controls. Each transmitter incorporates RFI/EMC and electrical spike protection. Features Process pressure range: 1.5 to 1,000 psi (0.1 to 69 bar) Accuracy of ± 0.25% of full scale Process temperature range: -40 to 250 °F (-40 to 121°C) 2-wire, 4 to 20 mA output CE and FM approved >>>
View the product on emcoflow.com EMCO Flow Systems
PROTRAN PR3100 PRESSURE TRANSMITTER

PROTRAN PR3100 PRESSURE TRANSMITTER
High stability and repeatable Supply Voltage 13-36Vdc All stainless steel housing 4-20mA, two wire output Zero and span adjustable Ranges 0-1 to 0-1000 bar Intrinsically safe models available Standard ranges EX-STOCK The PR3100 series pressure transmitters have been designed to meet the requirements of the majority of industrial applications of pressure measurement requiring an output of 4-20mA.Robustly constructed from stainless steel this range of pressure transmitters incorporates the latest strain gauge technology together with a custom IC amplifier offering excellent stability and accuracy over a long service life. Output options include 0-5vdc, 0-10vdc and 0-20mA. >>>
View the product on esi-tec.com ESI Technology Ltd
OIL PRESSURE TUBING KIT DHK

OIL PRESSURE TUBING KIT DHK
The Deluxe (DHK) oil pressure tubing kit can be used with a variety of Murphy SWICHGAGE® and MURPHYGAGE® instruments. This kit consists of gauge fitting, pressure tubing, and engine fitting. The Deluxe kit is ideal for heavy-duty industrial applications. The nylon core is reinforced with a synthetic fiber braid and polyurethane cover. Both ends of the pressure tubing have swaged fittings. >>>
View the product on fwmurphy.co.uk Frank W Murphy
INDUSTRIAL PRESSURE TRANSMITTER

INDUSTRIAL PRESSURE TRANSMITTER
Industrial pressure transmitter The PTX 1240 industrial pressure transmitter has been designed for use with aggressive pressure media found in many industrial and process applications. The fully welded 316L stainless steel pressure module ensures excelent media compatibility without compromising performance of Druck's micromachined silicon pressure sensing element. Product Description The PTX 1240 is intrinsically safe and explosion-proof certified, thus making it suitable for use in the oil and gas industry. Features & Benefits Pressure ranges 2.5 to 15000 psig;5 to 15000 psia Accuracy: ±0.25% FS BSL NACE MR 01-75 compatible Low Cost Class I, Div 1 Intrinsically Safe, Groups A,B,C,D Class I, Div 1 Explosion-proof >>>
View the product on ge.com/sensing GE Sensing
MELT PRESSURE SENSORS - K SERIES (NAK)

MELT PRESSURE SENSORS - K SERIES (NAK)
Pressure ranges from: 0-35 ato 0-1000 bar / 0-500 to 0-150000 psi Accuracy: < ±0.25% FSO (H); < ±0.5% FSO (M) Hydraulic transmission system for pressure signal guarantees stability at working temperature (NaK). Liquid conforming to RoHS Directive. NaK is defined as a safe substance (GRAS). Quantity of NaK contained per model: KN0 series (30mm3) (0.00183 in3) , KN1, KN2, KN3 (40mm3) (0.00244 in3) 1/2-20UNF, M18x1.5 standard threads; other types available on request Autozero function on board / external option Stem drift Autocompensation function (SP version) Inconel 718 diaphragm with GTP coating for temperatures up to 538°C (1000°F) 15-5 PH diaphragm with GTP coating for temperatures up to 400°C (750°F) HastelloyC276 diaphragm for temperatures up to 300°C (570°F) 17-7 PH corrugated diaphragm with GTP coating for ranges below 100 bar-1500 psi >>>
View the product on gefran.com Gefran CRL Ltd
BASIC PRESSURE SENSORS SCC

BASIC PRESSURE SENSORS SCC
The SCC series offer an extremely low cost sensor element with a temperature stable output when driven with a constant current source. These integrated circuit sensors were designed for extremely cost sensitive applications where precise accuracy over a wide temperature range is not required. This series is intended for use with non-corrosive, non-ionic working fluids such as air and dry gases. Absolute devices have an internal vacuum reference and an output voltage proportional to applied pressure. The differential devices allow application of pressure to either side of the diaphragm and the devices are thereby available to measure both differential and/or gage pressures. >>>
View the product on haleinst.com Hale Instruments Ltd
PRESSURE COMPARATOR 10,000 PSI – 700 BAR - GAUGECALXP™

PRESSURE COMPARATOR 10,000 PSI – 700 BAR - GAUGECALXP™
The GaugeCalXP™ is a self-contained precision hydraulic pressure generator intended for the calibration of pressure gauges rated up to 700 bar or 10,000 PSI. It can be filled with your choice of fluid: water, oil or isopropyl alcohol and can be easily moved from one location to another. The GaugeCalXP™ is much faster to use than a deadweight tester and is also faster than most automated pressure controllers, but it costs less than either. It is ideal to calibrate those low cost gauges that are often overlooked for ISO9001 compliance. The features and performance of the GaugeCalXP™ make it the perfect solution for even the most demanding gauge calibration requirements. >>>
View the product on haven.co.uk Haven Automation
VISTA-GAGETM HI-PRESSURE GAUGE

VISTA-GAGETM HI-PRESSURE GAUGE
Operates with liquids or gases Pressure range: 20 to 5,000 psi (1.4 to 345 bar) Rugged construction: - Body: CA360 brass - Piston: Stainless steel - Internal shaft: Stainless steel - Spring: Carbon steel - Guard: High impact lexan plastic Thread: 1/4 inch NPT Operating pressure: 5,000 psi (345 bar) maximum Operating temperature: -40 to 240 °F (-40 to 116 °C) maximum Accuracy within ±5% of full scale Rugged cylindrical design offers 360° readability Withstands shock, vibration, and overpressurization Eliminates costly snubbers No bourdon tube to blow out Installs in any angle Standard scale: Vertically graduated numerals in PSIG and Bar increments >>>
View the product on hedland.com HEDLAND Groupe - Racine Federated
HIGH INTEGRITY PRESSURE PROTECTION (HIPPS)

HIGH INTEGRITY PRESSURE PROTECTION (HIPPS)
The Karsto Gas Processing Plant involves the subsea and subterranean transportation of oil and gas between the Karsto plant on the East coast of Norway and the Asgard Offshore oil field. NET 1 involved the introduction of a new Emergency Shutdown System and High Integrity Pressure Protection System on the plant ands was completed in September 2002. The KEP 2005 (Karsto Expansion Project) comprises of additional systems logic using the HIMA Planar4 solid state technology, accompanying marshalling cabinets and interposing relay cabinets to cope with the increased throughput of the plant, which is now recognised as the largest in Europe. >>>
View the product on hima-sella.co.uk Hima Sella Ltd
SERIES 700 PRESSURE, DP & TEMPERATURE SWITCHES

SERIES 700 PRESSURE, DP & TEMPERATURE SWITCHES
HNL's most popular switch range! The Series 700 switch range is available for the measurement of pressure (P & PZ) and differential pressure (DP & DPZ). There are pressure ranges for the measurement of gauge pressure above atmospheric pressure (P) and below atmospheric pressure (PZ). Also available for the measurement of temperature (T). For each of these both Electrical and Pneumatic outputs are available. The electrical outputs are available for switches to be used in Hazardous (potentially explosive atmosphere) areas (Exd, ExnC & ExtD, Exia or I.S. compatible) or for Standard (non-hazardous) areas. >>>
View the product on hnl-uk.com HNL Instruments & Controls Ltd
PRESSURE TRANSMITTER TYPE 510

PRESSURE TRANSMITTER TYPE 510
Relative pressure transmitter for refrigeration technology Type 510 -1 ... 7 - 160 bar These compact OEM pressure transmitters type 510 have been developed for applications in the industrial refrigeration technology. The special sensor is based on thick-film technology, developed by Huba Control, which utilises a special grade of steel welded to the pressure sensor. This means that the 510 can be used for all gases and media in refrigeration, including ammoniac. Highest requirements concerning EMC and accuracy for all temperature ranges can be met in combination with the unique integrated electronic design. Pressure ranges Customer side - 1 ... 160 bar (minimum 7 bar fs) - 14.5 ... 2000 psi (minimum 100 psi fs) Minimum order quantity: 250 pieces >>>
View the product on hubacontrol.com Huba Control


123Suivant >>Fin >
Go to page


  Search    
 
 
 
Search
See all of the sector's products : Measuring devices, analysis and sensors