Milling: suppliers, wholesalers and manufacturers on Hellopro
Search   


Milling :

385 products
Select the category
    Selection of 120 products among 385
    MIRCONA RANGE - SLOT & GROOVE MILLING TOOLS

    MIRCONA RANGE - SLOT & GROOVE MILLING TOOLS
    Advanced Carbide Tooling offer the exclusive range of Mircona slot and groove milling toolsMircona slot and groove toolsA complete range of slot and groove milling cutters are offered by Mircona to cover most machining operations performed by these tools.The Mircona slot milling cutter is used for deep grooving or cut-off.Due to the design of the patented clamping system, consisting of a sprung loaded integral top clamp, the clamping force on the insert increases proportionally with the cutting force.The clamping is based on a reverse angle on the insert seat, which effectively ”dove tails” the insert into position and completely eliminates the risk of the insert being thrown centrifugally out of the milling cutter body. >>>
    View the product on advancedcarbidetooling.co.uk Advanced Carbide Tooling Ltd
    MACHINE MIKRON HSM 400 MILLING CUTTERS

    MACHINE MIKRON HSM 400 MILLING CUTTERS
    Experience shows that the advantages of high-speed milling can only be realized at cut speeds of more than 40'000 min-1, high feedrates and the best accelerations available – especially in the case of small milling cutter diameters for tool and mould manufacture. These basic requirements call for all the machine components to be fully adapted to HSC technology. That is why the basic structural design, the high speed spindles, the control system, the feed drives, the axis mechanism and the automation of Mikron's HSM range all have been designed with high speed machining in mind. >>>
    View the product on agie-charmilles.com Agie Charmilles
    MILLING TOOLS - MONOCUT

    MILLING TOOLS - MONOCUT
    Using the Face and Right Angle Milling Heads Particular milling strategies must be followed for the optimum use of our MonoCut Milling Tools due to the different ultrahard cutting materials. The following shows an overview of the cutting widths with reference to the respective cutting diameter as well as the minimum and maximum depth of cut and the feed rate per tooth. The direction of feed must be taken into consideration along with the cutting width: 1) BL and BH down-cut milling 2) DP down-cut milling, and up-cut milling under certain circumstances 3) DM down-cut or up-cut milling The best surface quality in face milling at a cutting depth of max. 0,3 mm is achieved by complete assembly with large wiper edges. The other MonoCut Inserts Geometries mean that a high chip capacity with the best surfaces is no problem in countless combinations. The numerous variations possible with this Milling System, which does not require timewasting adjustment procedures, offer highest productivity and flexibility for the professional use of all ultrahard cutting materials. >>>
    View the product on beckerdiamant.de Becker-Diamantwerkzeuge
    CNC MILLING MACHINE FCN-P

    CNC MILLING MACHINE FCN-P
    Computerized Numerically Controlled Milling Machine (CNC), FCN-P model, specially designed for the machining of considerably long parts. Agile and robust machine prepared to work on technical, thermoformed plastics and composites. The machine has 3 CNC controlled axes and a high speed air-cooled milling head of 8 kW. The tool change is revolver type and the cone geometry is ISO-30. The working table has a usable dimension (squared are) of 3.100 mm x 2.100 mm. As an option, it can be built bigger at 4.000 x 2.000 mm. The parts are held on the table by a vacuum pump of 140 m3/h. >>>
    View the product on bermaq.com BERMAQ
    AREA TYPE MILLING MACHINES

    AREA TYPE MILLING MACHINES
    The AREA series moving gantry machines are a multi-purpose milling and engraving system develop from BIEMMEPI SISTEMI based on years of CNC milling machine manufacturing experience .The bed-plate is made of electro-welded stabilized steel and it’s designed to guarantee excellent mechanical stiffness and superior dynamic stability. The gantry, on which the X-axes carriage is assembled ,has been designed using one solid piece of stabilized steel. The X and Y axes movements were designed with helical toothed ground racks and pinions, the linear guides were designed with caged balls and the Z axe travel (265 mm) incorporates a ground ball screw lifting system. The fully digital BMPDIGIT numerical control has a user-friendly interface, based on Windows CE. A hand-held keypad interface with a LCD display allows the operator to control all the machine functions including jogging the machine, setting work parameters, tool preset, origin settings and remote computer system works file download (G-code or HPGL). The automatic tool change system spindle is for ISO30 shank tool holders and has a power of 8Kw. The manual tool change system spindle has a power of 6Kw and ERG32 tool holder collet. Three different Area models are available: AREA S: 1640x1025x265 mm AREA M: 2540x1525x265 mm AREA L: 3040x2025x265 mm >>>
    View the product on biemmepi.it BIEMMEPI SISTEMI
    GROOVE MILLING

    GROOVE MILLING
    Groove Milling The circular milling principle allows outside and inside contours to be machined to individual requirements on all CNC Machining Centres. High efficiency is achieved by increased speeds and feeds, extended tool life and reducing or eliminating expensive special tools. - Type 04/03 Minimum bore 8mm x 1.6mm depth of cut - Type 02 Minimum bore 11mm x 2.65 depth of cut - Type 01 Minimum bore 20mm x 3.45 depth of cut - Type 023 Minimum bore 33mm x 4.0mm depth of cut - Type 013 Minimum bore 63mm x 6.0mm depth of cut >>>
    View the product on bluechiptooling.co.uk Bluechip Tooling Ltd
    CNC BED TYPE MILLING MACHINES (BVA RANGE)

    CNC BED TYPE MILLING MACHINES (BVA RANGE)
    Broadbent Stanley's range of CNC Bed Type Milling Machines have passed strict quality control tests to incorperate state of the art technology.With advanced numerical control systems to provide solutions for milling, scanning, digitalisation and compatability with CAD/CAM systems, the BVA range becomes the most cost effective solution on the market.ConstructionThe bed, column and table are constructed of high grade Mehanite castings, normalised and aged to achieve maximum stability.The design features heavy cross ribbingfor rigidity and vibration dampening.The bedways are hardened and precision ground.8 machine sizes to choose fromBV/A - Table - 356mm x 1270mmB2V/A - Table - 406mm x 1372mm >>>
    View the product on broadbentstanley.co.uk Broadbent Stanley Machine Tools Ltd
    MILLING MACHINE - S-191

    MILLING MACHINE - S-191
    S-191 : 6-axis Milling Machining Centre Main characteristics Possibility to execute milling operations on up to 5 simultaneous axis Cast iron construction providing high rigidity and vibrationfree operation Rotating axis with direct-drive technology offer extremely high precision and accuracy as well as clearance-free operation Re-taking gripper for milling operations on the sixth side Possibility to use an automatic bar loader or a pushing-bar device Applications Horological industry Jewellery industry Medical Field Light industry >>>
    View the product on bumotec.ch BUMOTEC
    TOOLS GRINTA - MILLING CUTTER

    TOOLS GRINTA - MILLING CUTTER
    GRINTA is a new D’Andrea solution for milling operations. The program comprises a series of milling cutter bodies that utilize classical milling cutter geometry styles and ISO inserts, thereby increasing the working range of the MHD’ Modular System. The MHD’ Modular System, already known worldwide for its roughing and finishing boring tools, now makes available to the milling operation its large-capacity and its inherent perfect concentricity and extreme resistance to torsion. At the heart of the system is the coupling: for diameters from 16mm to 32mm the GRINTA system takes advantage of dual couplings, that is, the milling heads have a threaded end along with a ground guide accompanied by the modular MHD’ connection. For cutter diameters 40mm, 50mm and 63mm, the cutter bodies incorporate the modular MHD’ connection. >>>
    View the product on dandrea.com D Andrea S.p.A.
    MILLING SERIES DCN-ST MOD.DCNW 150 ST

    MILLING SERIES DCN-ST MOD.DCNW 150 ST
    Plate 1500x1500-1500x1750 Capacity load 12000 Kgs Stroke 800-1000-1500-2000 mm CN rotary and shifting table for milling operations - W axis configuration - Cast iron and steel structure - Table mechanical drive through worm screw - Slide mechanical drive through recirculating-ball screw - Hydraulic clamping of the axis - Hydrostatic support system of the plate Optional: Heidenahin encoder table series RON 200/700/800 Heidenhain encoder slide series LS 186C Table motor drive Siemens series 1FT6-105 Slide motor drive Siemens series1FT6-108 >>>
    View the product on delken.it Delken Automazioni
    UNIVERSAL MILLING - DMC 635 V ECO

    UNIVERSAL MILLING - DMC 635 V ECO
    3-axis vertical milling with 3D-simulation in an unbeatable package priceThe standard version of the DMC 635 V eco Vertical Machining Centre offers numerous lucrative high-tech features, such as the powerful 8,000 rpm milling spindle, the 20x tool magazine, as well as highly dynamic axis drives with feeds up to 25 m/min. In addition, benefit from state-of-the-art CNC control technology with ShopMill software or Fanuc with Manual Guide i software. The new DMG ECOLINE: High-tech features at an unbeatable price! >>>
    View the product on dmguk.com DMG UK
    EDGECAM MILLING

    EDGECAM MILLING
    Production Milling Edgecam provides the production machine shop with a wide range of flexible milling cycles. Machining efficiency is maximized on simple and complex prismatic parts as well as those incorporating sculptured surface geometry. With Edgecam you get prismatic machining combined with powerful 3D solid and surface machining strategies, all in one complete solution. 4- and 5-Axis simultaneous machining Edgecam 4 and 5-Axis milling products are designed to meet the production machining requirements of industries such as aerospace, automotive, medical and oil & gas. 4- and 5-Axis simultaneous machining offers key advantages over conventional indexed 3-Axis machining: Reduced cycle time by machining complex components using a single setup. In addition to time savings improved accuracy can also be achieved as the potential for positioning errors between setups is eliminated. Improved surface finish and extended tool life by tilting the tool to maintain the optimum tool to part contact point at all times. Improved access to undercuts and deep pockets through tilting the tool or component allows shorter series tooling to be employed, further improving the surface finish and eliminating the need for secondary setups. The ability to machine complex parts from solid that would previously have to be cast. This approach is highly beneficial for prototypes and small volume runs and is particular applicable with the latest Mill/Turn machines. >>>
    View the product on pathtrace.com Edge Cam
    PRODUCTION SYSTEM - ULTRA MILLING AND CUTTING CENTER

    PRODUCTION SYSTEM - ULTRA MILLING AND CUTTING CENTER
    CNC milling and cutting centre with 28 controlled axes in fully automatic mode, designed for machining profiles made of aluminium, PVC and light alloys in general. Right from the entry of the extruded bar until the exit of the finished part, simultaneous machining operations are performed on all four faces of the profile. The system features 16 electro-spindles (8 horizontal opposed spindles and 8 vertical opposed spindles), 2 cutting units, N/C overhead loader and unloader, 26 axes, 6 automatic vices. All such facilities allow considerable reduction in times, down to one half. The multiprocess CNC control also allows working with several tools simultaneously. >>>
    View the product on emmegi.com Emmegi Group
    MILLING MACHINE - GBM 21/26/31

    MILLING MACHINE - GBM 21/26/31
    Teleservice and Ethernet. Automatic Huron Milling Head 2 positions (ver/hor). Automatic Huron Milling Head (2,5º/2,5º). 4.000 rpm on the Head. Automatic tool changer: - Static 5 or 10 Tools. - Random type 24 Tools. Portable electrospindles. Mechanical Spindle speed multipliers. Driving system preparation for 4th axis. Electronic rotary tables. Coolant through spindle (10 bar pressure). Chip conveyor. Electronic probe for toolsetting. Electronic probes for work piece set up. Different CNC systems available: HEIDENHAIN, FAGOR, FANUC, SIEMENS. Thermal compensations for Ram expansion: X, Y, Z axis. >>>
    View the product on goratu.com GORATU
    MILLING

    MILLING
    It used to be the case that the operation at hand predetermined the selection of the milling tool to perform the required function. Older conventional machine tools were limited to rotational spindle speed and table feed but more than made up for this shortfall with ample horsepower allowing bigger depths of cut to be taken. Nowadays modern CNC controlled machines with multi-task capability linked to sophisticated software packages are surpassing early expectations in terms of processing speed, reliability, and the number of operations carried out in a single set up. More often than not modern machines use high speed cutting techniques (HSC) employing smaller depths of cut matched to rapid feed movements in an attempt to reduce the vibration phenomenon which effects poor surface quality and premature tool failure. Continuous research and development expands the selection available from the new generation PMF-HSS tools through a wide ranging variety of solid carbide and micrograin carbide tools as small as 0.2mm diameter. These micro-cutters are available in lengths up to 15 times the diameter opening up a whole new application field for micro-milling. The spectrum of indexable tools with different approach angles for shoulder milling, facing, contouring and plunge milling has grown rapidly with the advent of machine tools with mill-turn capabilities which require multi-function tools designed to perform more than one task. It is important therefore to choose the correct machining concept and pay attention to the cutting forces that will be generated as a result of the application, with radial and axial engagement limited by the machine tool spindle taper and construction. >>>
    View the product on jemmatools.co.uk Jemma Tools Group
    LANG (MILLING) MACHINES: IMPALA 200

    LANG (MILLING) MACHINES: IMPALA 200

    The IMPALA 200 is a compact CNC-controlled engraving and milling machine with column. The special characteristic of the IMPALA-series is the solid granite foundation which greatly minimizes vibration and therefore guarantees high quality manufacturing. It is suited for the manufacture of coining dies, reliefs, moulds etc. in different materials and even stainless steel. The machine can be configured accordingly to each application by a wide range of accessories. Working range X x Y x Z:300 x 200 x 200 mm Clamping area:540 x 260 mm Feed rate, inside material:1,3 - 2,6 m/min Feed rate, outside material:2,6 - 5,2 m/min Load bearing capacity (work piece and accessories)age/pj:150 kg Max. acceleration:0,14 m/s² Spindle speed:5.000 - 60.000 rpm Spindle output:0,3 - 2,6 kW Overall dimensions X x Y x Zbitm:1.350 x 1.300 x 2.450 mm Weight of the machine:1.100 kg Options: * Circular engraving devices * Tool changing systems * Vacuum clamping systems * Coolant and lubricating systems >>>
    View the product on lang.de LANG
    TWIN SPINDLE MILLING HEAD - SERIES TSI AND TSX

    TWIN SPINDLE MILLING HEAD - SERIES TSI AND TSX
    The heads serial TSI and TSX with parallel or convergent spindles are suitable to mill and to chamfer teeth. Particular care has been drawn on scating and on disposal of the spindles bearing, because tools in hard metal are used to chamfer all gear teeth and they have to stand continuos strong crashes. The result has been a solid construction of good look and with reduced overall dimension. The body is in light alloy, the spindle supports in cast iron and the gear in heat treated steel. The spindles may turn in the same direction or in apposite direction and the rotation of both spindles is achieved thanks to a single act. The tool connection may be cylindric or with spring collets. The lubrificant is obtained by long life grease. The production of our twin milling heads has been possible thanks to the experience acquired in multispindle head construction, to the acquaintance of manufacturing process and to the skill, whick allows us to advise qualified and reliable product for every particular need. >>>
    View the product on omgnet.it OMG
    EDGECAM MILLING

    EDGECAM MILLING
    Production Milling Edgecam provides the production machine shop with a wide range of flexible milling cycles. Machining efficiency is maximized on simple and complex prismatic parts as well as those incorporating sculptured surface geometry. With Edgecam you get prismatic machining combined with powerful 3D solid and surface machining strategies, all in one complete solution. 4- and 5-Axis simultaneous machining Edgecam 4 and 5-Axis milling products are designed to meet the production machining requirements of industries such as aerospace, automotive, medical and oil & gas. 4- and 5-Axis simultaneous machining offers key advantages over conventional indexed 3-Axis machining: Reduced cycle time by machining complex components using a single setup. In addition to time savings improved accuracy can also be achieved as the potential for positioning errors between setups is eliminated. Improved surface finish and extended tool life by tilting the tool to maintain the optimum tool to part contact point at all times. Improved access to undercuts and deep pockets through tilting the tool or component allows shorter series tooling to be employed, further improving the surface finish and eliminating the need for secondary setups. The ability to machine complex parts from solid that would previously have to be cast. This approach is highly beneficial for prototypes and small volume runs and is particular applicable with the latest Mill/Turn machines. >>>
    View the product on pathtrace.com Pathtrace Ltd
    ROEMHELD VICES 5-AXIS MILLING MACHINES

    ROEMHELD VICES 5-AXIS MILLING MACHINES
    When Hemlock Engineering Ltd invested in two of the fastest 5-axis milling machines in the world in 2005, they knew that they needed vices that would help them maximise the machining capabilities. That is why they specified Hilma SCS120 and SCS80 vices from Roemheld. Nick Marks, Technical Support Engineer for Hemlock, said: “There was no point buying expensive machines and skimping on the vices as speed and balancing is vital. Accuracy and repeatability are also key and you cannot afford to be even a few microns out as it can cause larger errors and mismatches by the time the work piece has been moved in several axes. We often hold large pieces of metal on the 3mm lip of the Hilma vices in the knowledge that the parts will be held securely and safely. I had used Roemheld before and knew they would be the right choice for our 5-axis requirements.” >>>
    View the product on roemheld.co.uk Roemheld (UK) Ltd


    123Suivant >>Fin >
    Go to page


      Search    
     
     
     
    Search
    See all of the sector's products : Manufacturing and processes