Selection of 120 products among
7368
ULTRASONIC TRANSDUCERS
For applications requiring high ultrasonic power, Cedrat Groupe distributes in France and all over Europe the Ultrasonic Industrial Processors (UIP), which are ultrasonic Langevin transducers made
by Hielscher, a German partner company. Hielscher's wide product range of ultrasonic processors for industry allows for a seamless scale up from lab samples to bench top or prototype units and most essential to full industrial scale. The power spectrum for the industrial applications reaches at the time from 12 up to 16,000 watts per single processor. These ultrasonic processors are used for many applications such as welding, cutting, homogenizing, emulsifying, disintegration or deagglomeration and dispersion in production process. There, Hielscher systems are replacing common technologies, such as shear pumps and high pressure homogenizers due to their high efficiency and low maintenance. For specific industrial applications where an ultrasonic treatment could improve a production process, Cedrat Technologies can provide customer services for helping in the integration of Ultrasonic Industrial Processors (UIP).
>>>
View the product on cedrat.com/
Cedrat Technologies
SENSOR ACCESSORIES 200100
1/2-20 UNF Pressure Sensor Mounting Hole Cleaning Kit
The Dynisco cleaning kit was designed for checking mounting hole dimensions and removing excess plastic from the mounting holes prior to
installing melt pressure and temperature sensors. Installation of transducers into improperly machined, cleaned or improperly sized holes is the number one cause of damage to melt pressure sensors.
This kit will allow a user to clean the 0.312" tip diameter hole, the 45 degree seating surface, and the 0.451" hole. The kit includes a gauge plug which is used to verify that the hole has been correctly machined and cleaned.
M10 and M18 kits are also available.
Important:
The cleaning tool must be used when the polymer is in a semi-molten state. Care must be taken not to exceed a torque rating of 100 inch - pounds during scraping so as not to damage the cutting edges of the tool. These cutting edges are manufactured from hardened tool steel and will not wear if reasonable care is exercised. It is strongly recommended that a high temperature lubricant be applied to the tap and the threads of the guide sleeve and gauge plug to prevent seizing.
Sensor Accessories
200100
1/2-20 UNF Pressure Sensor Mounting Hole Cleaning Kit
The Dynisco cleaning kit was designed for checking mounting hole dimensions and removing excess plastic from the mounting holes prior to installing melt pressure and temperature sensors. Installation of transducers into improperly machined, cleaned or improperly sized holes is the number one cause of damage to melt pressure sensors.
This kit will allow a user to clean the 0.312" tip diameter hole, the 45 degree seating surface, and the 0.451" hole. The kit includes a gauge plug which is used to verify that the hole has been correctly machined and cleaned.
M10 and M18 kits are also available.
Important:
The cleaning tool must be used when the polymer is in a semi-molten state. Care must be taken not to exceed a torque rating of 100 inch - pounds during scraping so as not to damage the cutting edges of the tool. These cutting edges are manufactured from hardened tool steel and will not wear if reasonable care is exercised. It is strongly recommended that a high temperature lubricant be applied to the tap and the threads of the guide sleeve and gauge plug to prevent seizing.
Features:
Cleaning drill - P/N 200904
Cleaning drill guide - P/N 200906
Handle - P/N 200907
Gauge plug - P/N 200908
Bottoming tap - P/N 200905
Allen hex wrench - P/N 200909
Dykem blue - P/N 200910
>>>
View the product on dynisco.com
Dynisco (UK) Ltd
STAINLESS STEEL BUCKETS - MEASURING JUGS ETC
NEW STAINLESS STEEL BUCKETS :: MEASURING JUGS ETC.
E-Components & Chains Limited of Pocklington UK are pleased to announce the launch of their very own range of Stainless Steel Food Processing
items including buckets, scoops, scrapers, shovels, jugs, funnels etc.
Stainless steel's beneficial properties have led to its application throughout the food chain. From food processing and brewing, through distribution and storage to serving food, installing ECC`s stainless steel equipment brings unique benefits to the food and pharmaceutical industry.
One of the great advantages of our ECC stainless steel range is that it imparts no taste to the food/products that is prepared on it. Typical uses include kitchens, dairies, ham curing and fish storage. The grades used by ECC are 304, for ambient temperatures and low acid concentrations, and 316 for harsher environments. For example 304 is used in cheese and dairy production, but where salted (ham) products is being prepared 316 is used. In ice cream production /processing 316 is specified because strong anti-bacteriological cleaning and rinsing systems are used.
A further advantage is that stainless steel is resistant to damage caused by condensation cycles in high humidity areas such as kitchens etc.
ECC are confident this new and exciting range of Stainless Steel products will greatly enhance their ever expanding range of Detectamet metal detectable products currently being used and specified by some of the worlds leading food and pharmaceutical manufacturing / processing companies.
>>>
View the product on ecc-ltd.co.uk
E-COMPONENTS & CHAINS LIMITED
FB420 SHAFT SPEED SENSOR
• Compact, self-contained system with sensor and switch
• Simple installation and calibration
• Relay can be set for over-speed or under-speed
• Rugged housing is explosionproof and waterproof -
NEMA 4X
• 4-20mA output directly proportional to shaft speed
• Provides real time preventive maintenance feedback
• Prevents product waste, machinery damage and
process downtime
Description
Electro-SensorÂ’s FB420 is a shaft speed sensor that provides a 4-20mA signal directly proportional to the rotational speed of a
monitored shaft. Since both the 4mA and 20mA calibration points are programmable the user can also operate the FB420 with the
4mA offset from 0 RPM. The FB420 has a 4 digit LCD display used for calibration and trouble-shooting. The LCD is capable of displaying
from 0.000 to 9999. RPM or from 04.00 to 20.00 mA. The FB420 has one relay that can be programmed for failsafe over-speed alarm
or failsafe under-speed alarm.
Housed in a rugged, explosionproof NEMA 4X housing, the FB420 is ideal for detecting shaft under-speed or over-speed on a wide
variety of industrial machinery. Typical applications include belt conveyors, drag conveyors, bucket elevators, fans, blowers, crushers,
and pumps. The FB420 is compatible with a wide range of pulser discs and wraps, and can be mounted using the optional EZ100
and stainless steel discguard when required. Electro-SensorsÂ’ products bring efficiency and safety to your operations by preventing
machine damage, product waste and costly downtime.
Pulser Disc
The end of the shaft to be monitored must be center drilled to
a depth of 1/2-inch with a #21 drill and tapped for a 10-32 UNF.
After applying Loctite™ or a similar adhesive on the threads to
keep the pulser disc tight, the pulser disc should be attached,
decal side out with the supplied 10-32 UNF machine screw and
lock washer. Dimension (A) is 1/16 inch to 1/4 inch.
The center-line of the magnets (B) must align with the center
of the sensing head as the Pulser disc rotates.
Pulser Wrap (optional)
Pulser wraps are custom manufactured to fit the shaft they will
be mounted on. When the wrap is shipped, four Allen-head
cap screws hold the two halves of the wrap together. These
screws must be removed so the wrap is in two halves. Place
the halves around the shaft, reinsert the screws and torque
them to 8 foot-pounds. Dimension (A) is 1/16 inch to 1/4 inch.
The center-line of the magnets (B) must align with the
center of the sensing head as the PulserWrap rotates.
FB420 • Specifications
Input Power
Voltage .............................................................. 24 Vdc ± 10%
Current .............................................................. 55 mA with 20 mA signal and
relay energized
Input Signal
Type...................................................................... Magnetic alternating
Range of Operation ................................ Overall = 0.1Hz to 9999Hz
(with 8 PPR = 0.75 RPM to 9999* RPM)
*The LCD can only display up to 9999
Gap Distance ................................................ 1/16” to 1/4”
Analog Output Signal
Type...................................................................... 4-20 mA, with programmable endpoints:
(4 mA @ userÂ’s Min RPM)
(20 mA @ userÂ’s Max RPM)
Accuracy .......................................................... ± 0.7%
4-20 mA Resolution ................................ Depends on calibration, but can be a
best of 0.001 mA per increment
Required Impedance.............................. 4-20 mA output needs a 250 to
500 load
Analog Output Signal (cont.)
Max Signal Distance .............................. Using a 3-conductor cable with
17.5 /1000 ft per conductor, the
maximum length of cable usable
with the FB420 is:
• 3800 ft when not using the relay
• 2300 ft. when using the relay
Relay Output Data
Number Available...................................... 1 SPDT Form C
Relay Contact Rating.............................. 5 amp @ 30 Vdc, 5 Amp @ 250 Vac
Relay Functions .......................................... Fail-safe alarm state is relay
de-energized:
• Unused • Fail-safe Over-speed
• Fail-safe Under-speed
Physical /Environment
Normal Operating Temp .................... -40° C to +65° C (-40° F to +149° F)
Storage Temp .............................................. -40° C to +80° C (-40° F to +176° F)
Humidity .......................................................... 0% to 90% non-condensing
Ratings .............................................................. NEMA 4X. UL rated for XP hazard
groups C, D, E, F and G
>>>
View the product on electro-sensors.com
Electro-Sensors
BATTERY POWERED "STAND ALONE" MEASURING UNIT - Z 16 / Z 17
Battery powered "stand alone" measuring unit - Z 16 / Z 17 (single axis)
Functions
The flexible magnetic tape makes also angular
measurements possible and is
available in lengths up to 33
meters.
Up/down function
2 tool offsets adjustable
Up/down switch over
Pulse factor
Selectable decimal point
Adjustable reference value
Inch/mm switch over
Switchover for absolute/incremental measurement
Fraction-display in "inch" mode possible
Mountig angle and guide carriage as accessories
Features
No more wiring is necessary! This battery powered LCD-Indicator is already combined with a magnetic sensor. The system is predestined for mounting on movable slides and stop-systems.
With a good battery the system's able to work up to 12 months in continuos operation.
The incremental measuring system Z16 measures movements directly, that means there are no pitch or measuring errors due to mechanical play.
The distance between magnetic sensor and magnetic tape may be up to 0.8 mm's without impairing system accuracy.
Technical specifications:
LCD display: 7 digits with sign, digit height 11mm
Power supply: commercial 1.5 V battery
Power consumption: approx. 1 mA
Operation speed: maximum 2.5 m/sec
Resolution of magnetic sensor: 0.1 mm
Housing: black aluminium panel housing
Housing dimensions: width 96 mm x height 72 mm
Cut out: Z16: W = 92 mm x H = 66 mm
Z17: W = 96 x H = 48 mm
Installation depth: Z16: 40 mm
Z17: 43 mm
Protection class: IP40 (installed state)
Technical specifications of magnetic sensor:
Length of sensor cable: 0.1 m to max. 1.0 m
Protection class: zinc die cast housing IP67
Operating temperature: + 5...+ 50 ° C
Bend radius/cable: min. 60 mm
Distance sensor/tape: maximum 0.8 mm
Install position: any
>>>
View the product on elgo.de
ELGO-Electric
