Instrumentation thermique (translation in progress): suppliers, wholesalers and manufacturers on Hellopro
Search   


Instrumentation thermique (translation in progress) :

584 products
Select the category
Selection of 41 products among 584
9500P DIGITAL PROGRAMMABLE PROCESS CONTROLLER

9500P DIGITAL PROGRAMMABLE PROCESS CONTROLLER
Features of the 9500P programmable process controller. • Full PID auto-tuning process controller • Total of 3 outputs, from 4-20mA, 0-5v, 0-10v, SSR drive, relay • Input options: Thermocouple 2 or 3 wire PT100 0-50mV, 0-5V, 0-10V, 0-20mA, 4-20mA • Alarms with 5 options • Heat-cool operation • Programmer operation • Sleeve mounting for easy maintenance • IP66 protection from front panel • CE, UL & CSA approvals • 3-year warranty • Monitoring and configuration software option • RS232/485 options, Modbus RTU protocol Programmer Features • Up to 31 programs (profiles) • Up to 126 segments • Unlimited use of event outputs via the 2nd and 3rd outputs • Copy/paste/edit/delete functions to simplify program building • Call another program as a sub-program segment • Up to 999 program loop cycles, or continuous loop cycling • Hold back function to ensure the next segment is not started until the last segment reaches set-point • 3 power fail recovery options, (hold, continue or reset) • Front Panel Interrogation of the program position • Memory usage indication during programming Front panel 'release from hold' function to run the program. Specification - 9500P Thermocouple types: 9 types: B,E,J,K,L,N,R,S,T Standards: IPTS/68/ DIN 43710 CJC rejection: 20:1 (0.05°/°C) typical External resistance: 100 ohms maximum Other input options: 0 to 50mV +/-0.1% 4-20mA +/-0.1% 0-5V +/-0.1% 0-10V +/-0.1% Applicable to all inputs (SM = sensor maximum) Calibration accuracy: +/- 0.25% SM +/-1°C Sampling frequency: input 10Hz, CJC 2 sec. Common mode rejection: Negligible effect up to 140db, 240V, 50-60Hz Series mode rejection: 60db, 50-60Hz Temperature coefficient: 50ppm/°C SM typical Reference conditions: 22°C +/- 2°C, rated voltage after 15 minutes settling time. Output devices (check configuration) SSd1 and SSd2 solid state relay driver: to switch a remote SSR 6VDC (nominal) 20mA non-isolated Miniature power relay: form A/SPST contacts (AgCdO) rLY1, rLY2, rLT3: 2A/250VAC resistive load Analogue output: 4-20mA 500 ohms max’ +/- 0.1% fs typical 0-5Vdc 10mA (500 ohms min’) +/- 0.1% fs typical 0-10Vdc 10mA (1K ohms min’) +/- 0.1% fs typical General: Displays: Upper, 4 digits, high brightness green LED 10.4mm (0.4") high. Lower, 4 digits, high brightness orange LED 9mm (0.35") high. Digital range –199 to 9999 Hi-res mode –199 to 999.9 LED output indicators – flashing SP1 square, green; SP2/SP3 round, red. Keypad: 3 elastomeric buttons. Power Supply: 100-240V AC, 50-60 Hz , (typ' 5.0 VA) >>>
View the product on cal-controls.co.uk CAL Controls
CORE THERMOMETER - TFX 410

CORE THERMOMETER - TFX 410
TFX 410 Core Thermometer (with fixed probe) Technical Data Measuring range -50 to +300°C Accuracy ± 0.2°C ± 1 Digit Resolution 0.1°C Sensor Pt 1000 (several types of probes available) Operating temperature -25 to +50°C Storage temperature -25 to +60°C Battery 3,0 V Lithium, changeable Battery life approx. 3 years Dimensions 54 x 22 x 109mm without probe Housing material ABS Weight approx. 90 g Protection class IP 67 Measuring rate 1s Certificate 3 point factory calibration >>>
View the product on ebro.de Ebro Electronic
0-10% SCALE CUTTING OIL REFRACTOMETER

0-10% SCALE CUTTING OIL REFRACTOMETER
Model: REF-101C Shipping Weight: 0.3Kg REF-101C visual hand held refractometer with Percent scale, range 0 to 10%, resolution 0.1%. For very low concentration samples where high precision is required. It is especially for degradation studies of cutting oils. Rugged, durable construction - made from corrosion resistant brass. High contrast demarcation line for easy, accurate readings. Easily adjusted zero line by means of readily accessible screw. Size 27 x 40 x 210 mm >>>
View the product on refractometers.com Index Instruments Ltd
FTI-E THERMAL IMAGERS

FTI-E THERMAL IMAGERS
High resolution radiometric thermal image, giving detailed temperature information transmitted via a high speed digital connectionAccurate temperature measurement, enabling optimum process control from over 76,000 individual temperature measurementsSimple installation and ease of use, reduces installation cost and complexityDesigned for harsh industrial environments, ensuring ultimate measurement reliability and availability >>>
View the product on landinst.com/infrared/index.htm Land Instruments International
1341 PLAIN JACKET CALORIMETER

1341 PLAIN JACKET CALORIMETER
The 1341 Calorimeter is an improved version of a plain, static jacket, oxygen bomb calorimeter that has been made by Parr for more than eighty years. It is a reliable calorimeter that can be used for the same broad range of solid and liquid combustible samples as the 6000 Series. Its modest cost and simple design recommend it primarily for users whose work load does not justify the purchase of an automatic model. The calorimeter requires no permanent connections. It can be set up and ready to operate in a few minutes and, when not in use, can be disassembled easily and stores on a shelf. >>>
View the product on parrinst.com Parr Instrument
BASE METAL THERMOCOUPLE ASSEMBLY WITH CERAMIC SHEATH - BMC

BASE METAL THERMOCOUPLE ASSEMBLY WITH CERAMIC SHEATH - BMC
Type Designation: BMC Temperature Range: -200 to 1700 ° C depending on sensor type Common Sensor Types: K, J, N, T, E Common Size : Ø 6.0, 8.0, 10.0, 12.0, 13.0, 15.0, 17.0, 20.0, 25.0, 28.0, 50.0mm Common Element Diameters: Ø 0.15mm to 0.5mm Shank: Plated MS, stainless steel , chrome iron, alloy 600 Heads: ALA, KNE (IP65), HR AL BL (flip top), many others Application Notes: Range of thermocouple types to choose from Will withstand tough industrial use Special Options: Special materials available on request Lining sheaths for porous materials available Shanks fitted for head assembly Adjustable or welded flange on shank Pressure tight design possible >>>
View the product on peaksensors.co.uk Peak Sensors Ltd
BATTERY POWERED THERMOMETER - DM540

BATTERY POWERED THERMOMETER - DM540
DM540 is a battery-powered Digital Thermometer which indicates the temperature with a selectable update rate and stores the maximum and minimum readings for later recall. The thermometer operates from standard AA alkaline batteries for over 2 years at the 12 second update rate. A selection of compatible temperature sensors are available with various immersion lengths and process connections. >>>
View the product on status.co.uk Status Instruments Ltd
3 PHASE ELECTRICITY METER

3 PHASE ELECTRICITY METER
Information The OFGEM approved three-phase electronic meters are designed for measuring kWh in three-phase four-wire networks. Available as CT operated or 120A direct connected. Features Fast and easy installation procedure, indicators show correct connection Smaller dimensions for overall cost reduction of the meter site Multi-phasing connection (all in one: single and poly-phase meter) Universal current terminals for all type of wires Indication of operational status Optical communication port for semi-automatic meter reading >>>
View the product on tmac-tech.com/ t-mac Technologies Limited
1/16 DIN DUAL DISPLAY PID TEMPERATURE CONTROLLER

1/16 DIN DUAL DISPLAY PID TEMPERATURE CONTROLLER
This powerful and versatile yet low cost PID controller has dual 4 digit display of process and set values and can be ranged by the user for a variety of inputs and alarms. This auto tuning controller also features continuous self tuning which in the majority of applications sets the controller up for optimum performance. - PID Auto tuning or On/Off can be selected - 1/16 DIN (48x48x100mm deep) - 4 digit dual LED display - Accuracy: Typically better than ±0.3% of FSV - 100-240V AC as standard. Contact us if you require 24V AC or 24V DC versions - Customer rangeable for Type K J T N E R S and B thermocouple or Pt100 inputs - Temperature (process or deviation) or Loop break alarms can be configured - Relay or Solid State Relay drive (SSR) or 4-20mA output versions - Non volatile memory - 3 year warranty >>>
View the product on tc.co.uk TC Ltd
RESISTANCE THERMOMETERS RT GP CH

RESISTANCE THERMOMETERS RT GP CH
The RT GP CH Series of Resistance Thermometers comprises of a range of sensors housed in 316 stainless steel sheaths and terminated directly into a connecting head. This provides a convenient method of termination and the terminal head contains connections in accordance with the wiring configuration chosen (2, 3 or 4 wire). A choice of sheath diameters, lengths and connecting heads is given below. The calibration and accuracy of these sensors conforms to BS EN60751 - IEC 751, 100? at 0°C. All sensors are supplied to Class A tolerance for enhanced accuracy. >>>
View the product on terwin.com Terwin Instruments
BENCH INSTRUMENTS - HIGH ACCURACY BENCH PT100 INSTRUMENT

BENCH INSTRUMENTS - HIGH ACCURACY BENCH PT100 INSTRUMENT
High accuracy microprocessor based PT100 instrument with the choice of display in °or °F. The instruments are housed in a tough ABS case and are supplied complete with integral tilt feet and 1.5m of cable with fitted mains plug. °C / °F switchable via rear mounted switch Resolution of 0.1° to 1000° autoranging Compatible with two, three or four wire sensors Overrance / Open circuit sensor indication Available as single or six input versions >>>
View the product on tmelectronics.co.uk/ TM Electronics (UK) Ltd
OIL TCU-TT-240

OIL TCU-TT-240
Temperature Control Unit Compact unit for use with oil up to 200ºC. Closed hot oil circuit with integral cold oil receiver in large expansion tank - long oil life due to low heater loads/high flow rate Self-optimising microprocessor controller with digital display of set and actual temperature Connection for optional external thermocouple Leakstopper – operation in pressure or vacuum mode, to allow continuous production despite leakage from mould or connections Automatic mould drain Automatic temperature control - audible alarm sounds when unit deviates outside 5ºC preset (adjustable). Heating switchable in stages Limescale-free heat exchanger No oil cracking No cooling-down required before switching off Safety devices: - level control provides auto dry run protection - electronic and mechanical safety thermostats - audible alarm in case of failure >>>
View the product on tool-temp.net Tool-Temp UK
B SERIES METAL BLOCK CALIBRATORS

B SERIES METAL BLOCK CALIBRATORS
Metal Block Calibrators B Series Metal Block Calibrators Features Ranges cover -25°C to +700°C Stability: Better than 0.05°C Excellent uniformity for accurate calibration Portable, safe and easy to use Over temperature safety cut-out Standard & custom inserts, to match your probe diameters and comply with IS09000 Use either upright or horizontal Use with an external reference thermometer or optional built-in Independent Indicator and probe Serial interface options Typical Applications Site Calibrations for PRT's, thermocouples and thermistors, with or without indicators Glass thermometers calibration Bimetallic switches calibration Dial Indicators (gas) calibration ASL's B series Metal Block Calibrators let you accurately calibrate PRT's and other thermometers easily and conveniently. These rugged, portable blocks provide a very stable and uniform temperature as standard, but you can specify the options to meet your needs precisely. For example, insert options let you use a wide range of probe diameters, saving time and money and, to allow accurate calibration required by IS09000, inserts with two or more holes accept both reference thermometer and the probes to be calibrated. The ASL range of Metal Block Calibrators consists of the B700 for temperatures from +50°C to +700°C and the B140 for temperatures from -25°C to 140°C. To aid rapid cooling from elevated temperatures to ambient ASL has developed the B-Cool forced air cooling probe. Metal Block Calibrators can be supplied with optional independent indicators and RS485 or RS232C interfaces. B700 Metal Block Calibrator The B700 allows you to accurately calibrate RTDs and other thermometers easily and conveniently. Its large capacity saves you time by holding up to 12 thermometers at once. Using ASL’s proven removable insert technology the B700 accepts a variety of temperature probe diameters and guarantees repeatable calibration performance to enable you to comply with your ISO9000 requirements. All B700s are tested over their full temperature range before dispatch and are supplied with a stability test certificate. >>>
View the product on aslltd.co.uk Automatic Systems Laboratories
IMMERSION PYROMETER DPP3

IMMERSION PYROMETER DPP3
DPP3 is a battery powered instrument with a 4 digit, bright: Green or Red LED display. The standard 1.25 metre steel dip arm, holding the thermocouple or its extension lead is normally hard wired and mechanically clamped into the DPP. Low battery voltage, broken thermocouple and reversed polarity are all indicated on the display when the 'ON' button in the handle is pressed. DPP is available for use with Type 'B','K','N','R' or 'S' thermocouples: Degrees C or F. >>>
View the product on northern-instruments.com Nothern Instruments (Leeds)
NC (NON-CONTACT) IR SENSORS - F-TYPE

NC (NON-CONTACT) IR SENSORS - F-TYPE
NC SENSOR - Our Non Contact (NC) sensor is a new concept in measuring infrared heat for temperature control. Utilising our own micro thermistor technology, we have developed a sensor which can be easily installed, is self-compensating and can withstand more aggressive environments than other conventional infra-red sensors. It is ideally suited for controlling the temperature of fuser rollers in laser printers and copiers. >>>
View the product on atcsemitec.co.uk ATC Semitec Ltd
INDUSTRIAL DOOR SENSOR

INDUSTRIAL DOOR SENSOR
The door sensor is designed to be used as part of a System5 in conjuction with a SCOUTPLUS and records the total number of minutes that the door has been opened during a given period. Available in Standard and Industrial versions Smallest time interval recorded: 5 seconds Smallest time interval displayed: 1 minute Data presentation: x minutes open during the corresponding log period, e.g. 3 minutes total open time in 10 minutes Short open times (less than 1 minute) rounded up to 1 minute Short closed times (less than 1 minute) rounded up to 1 minute Successive short openings during the same minute: recorded as one minute Dimensions of standard magnetic actuator : 80 x 80 x 20mm (smaller mechanical actuators also available for domestic style doors) Cable material: PVC screened Standard cable length: 1500mm (other lengths available to order) Dust / Waterproofing: IP67 when mated with ScoutPlus >>>
View the product on icespy.com Abacus IceSpy
ANVILLE SERIES 425 DATA LOGGER

ANVILLE SERIES 425 DATA LOGGER
The Anville series 425 system has 16 inputs for fifteen type T thermocouples and one pressure sensor input. Anville systems use Coto reed relay switching for thermocouple and pressure inputs. Reed relays have many advantages over semiconductor switching including 250VDC isolation between inputs, 400VDC isolation to ground, no thermoelectric EMF generation, no resistive offsets, long life and total reliability. Conversion to engineering units (°C/°F) is carried out by the microprocessor in the Anville system with data communicated to the computer in the correct engineering units enabling the system to have a traceable calibration certificate. An internal power supply provides the excitation voltage for the pressure transducer. >>>
View the product on anvilleinstruments.co.uk Anville Instruments Ltd
PNEUMATIC ACTUATORS HIGH TEMPERATURE

PNEUMATIC ACTUATORS HIGH TEMPERATURE
To pilot ball, butterfly and plug valves in high temperature ambients. ~ Designed to automatize fire security systems. ~ Constructed with metallic materials, inox and protected against corrosion by cataphoresis and special teflon. ~ Can be piloted with air and non agresive fluids, up to 8 bar (up to 15, on demand). ~ Models in Double Acting and Spring Return, with torques from 25 Nm. up to 2.000 Nm. at 6 bar. ~ Norms of construction: ISO 5.211, DIN 3.337, VDE 3.845, NAMUR. ~ Can withstand temperatures up to 265ºC. Certificate from the L.G.A.I. (Laboratori General d'Assaigs) >>>
View the product on gibsonexports.ltd.uk Gibson Exports Limited
DIGITAL THERMOSTAT - JUMO ETRON T

DIGITAL THERMOSTAT - JUMO ETRON T
JUMO eTRON T Digital thermostat with LC display for mounting on a 35mm DIN rail (70.1050)The JUMO eTRON T is a compact digital thermostat in 90mm x 22.5mm format for simple temperature control (heating or cooling). The measurement input permits the connection of resistance thermometers or thermocouples, or standard current or voltage signals. The measured value is shown on a 3-digit LC display. The switching status of the relay K1 is indicated by an LED.The instrument is operated from 3 keys on the front panel. The electrical connection is made via screw terminals.A setup program and a PC interface are available as accessories, for easy configuration and parameterization from a PC. >>>
View the product on jumo.co.uk JUMO Instrument Company
DO/PH/REDOX MONITORING - WQM-16S

DO/PH/REDOX MONITORING - WQM-16S
The WQM-16S combines SS and temperature measurements. This unit is intended for continuous operation to monitor the MLSS and produce the appropriate alarm and control signals. Typical applications can be found in activated sludge plants. Up to 8 SH2 probes can be interfaced to a single WQM-16S to monitor up to eight tanks. Alternatively, up to 5 tanks can be monitored for FE SS/turbidity and temperature. Or up to 4 tanks with MLSS, DO, and temperature monitoring. >>>
View the product on mdinstruments.co.uk MD Instruments Ltd
POINTSCAN® PRESSUREX® MEASUREMENT SYSTEM

POINTSCAN® PRESSUREX® MEASUREMENT SYSTEM
This easy-to-use tool prompts the user to enter temperature, humidity, time of exposure and film type, it then quickly displays the pressure reading in either Metric or English units of measurement. PointScan® is a durable device with multiple aperture dimensions which ensure accurate scanning of your surface pressure indicating film and it has a quick recalibration protocol that ensures high repeatability. >>>
View the product on sensorprod.com Sensor Products Inc


12Suivant >>Fin >
Go to page


  Search    
 
 
 
Search
See all of the sector's products : Measuring devices, analysis and sensors