Selection of 120 products among
396
ELECTRICAL CABLES - TRI-RATED CABLE
Eland Product Group: A2TApplication: Tri-rated Cable panel wiring is a high temperature, flame retardant cable designed for use in the switch control, relay and instrumentation panels of power
switchgear and for purposes such as internal connectors in rectifier equipment, motor starters and controllers. Tri-rated Cable is sometimes referred to as BS6231 Cable or Panel Wire.Standards: BS6231 Type CK UL Subj.758 CSA c.22.2 No. 127 (only applicable for sizes up to 120mm²) Conductor: Class 5 flexible plain copper conductors to BS EN 60228:2005 (previously BS6360)Insulation: PVC (Polyvinyl Chloride) Insulation Colour: Black, Red, Blue, Yellow, Green/Yellow, Grey,Brown, Orange, White, Violet, Green, Pink, Light Blue, Dark BlueVoltage Rating: BS6231: 600/1000V UL, CSA: 600VTemperature Rating: BS6231: 90°C (105°C for 15,000 hours) UL, CSA: 105°CMinimum Bending Radius: 6 x overall diameterNote: Cables above 120mm² in size are referred to as Bi-rated since the CSA standard applies only to sizes up to and including 120mm²
>>>
View the product on eland.co.uk
Eland Cables
FIBER OPTIC CABLE ASSEMBLIES
Connecting your equipment
Connectors
We can offer all common connector types used in the industry. The range includes SC, SC/APC, FC, ST, E2000, MT-RJ, LC, MU and MPO connectors with a connector
quality from >50 dB return loss. The fiber types could be standard single mode or multimode 50mm or 62,5 mm.
Features:
- full product range
- according to IEC 60874
- return loss >50 dB as standard
- single-mode or multimode fiber
- LSZH, UL-CMR and riser standard type
Pigtails
that can be spliced to the fiber in the cable when e.g. connecting an incoming cable into an ODF. Standard pigtail diameter is 900 mm. The connector range comprise SC, FC, ST, E2000, MT-RJ, LC, MU and MPO. Pigtails can be supplied with all standard connector types and in different lengths.
Features:
- full product range
- according to IEC 60874
- standard lengths
- single-mode or multimode fiber
- tight buffered, stripable in two steps
Fanouts
used when splitting multi fiber (ribbon) to single fiber. Fanouts will minimize splice cost when connectorizing the fiber cable within the ODF.
Features:
- single-mode or multimode fiber
- fiber range 4, 8, or 12 fiber
- standard lengths
Patch cords
Tailor-made patch cords with different connector types on demand, for example E2000 - SC.
Features:
- standard 2.0 mm diameter cable
- riser and plenum class
- tailor made design
- single-mode or multimode fiber
- LSZH, UL-CMR and riser standard type
Multifiber cable assembly
needed when interconnecting different equipment and when you want to concentrate a discrete fiber on a bundle. The cable assembly is a bundle of tight buffered fiber cables with 2 mm diameter and with connectors in one or both ends.
Features:
- from 4 to 24 fibers
- full product range of connectors
- connectors in one or both ends
- LSZH, UL-CMR and riser standard type
>>>
View the product on ericsson.fr
Ericsson
HIGH-POWER CABLE
High-Power Cable
For use with our turbines and PMG's, this cable is very flexible, High-Power with a 10sq mm conductor area (8 AWG), available in Red or Black. Ideal for connecting the DC power
output from our turbines, down your tower to your batteries, charge controller, heating element or inverter. Also good for making your battery bus bar connections. The cable is sold per meter, and has the following specifications...
Single core PVC insulated High-Power cable, ideal for use with wind turbines, batteries, power interconnections, charge controllers and heating element connections
Each cable contains 80 x 0.4sq mm plain annealed copper conductors with heat resisting PVC insulation rated up to +105 oC
UL, AWM, CSA, TEW, BS6231 and SEMCO recognised
Maximum working voltage: 600 Volts
10sq mm overall conductor area, suitable for currents up to 75A
Volt drop of only 2.2mV/A/m
Weight 1.2Kg per 10m
>>>
View the product on futurenergy.co.uk
Futurenergy Ltd
CABLE GLAND - 501/414
Application
Outdoor or Indoor use.
For use with non-armoured elastomer and plastic insulated cables installed in conduit.
Features
Provides a cable retention seal onto the cables outer sheath.
When
used in increased safety applications, this cable gland may be used with braided cable where the braid and the cables outer sheath pass into the enclosure. The braid must be suitably terminated into the enclosure.
Provides female running coupler for cable gland or conduit entry.
Materials & Finishes
The 501/414 Cable Gland is manufactured in Brass (standard, Nickel Plated Brass, 316 Stainless Steel or Aluminium.
Brass NPT entries are nickel plated as standard.
Technical Data
Flameproof Exd and Increased Safety Exe. II 2 GD
Baseefa Certificate No. Baseefa06ATEX0056X.
IECEx Certificate No. IECEx BAS 06.0013X.
Suitable for use in Zone 1, Zone 2, Zone 21 and Zone 22.
Suitable for use in Gas Groups IIA, IIB and IIC.
Construction and test standards EN 50014,EN 50018, EN 50019 and EN 50281-1-1. IEC 60079-0, IEC 60079-1 and IEC 60079-7.
IP 66, IP67 and IP68 (30 metres for 7 days) ingress protection to IEC 60529 and EN 60529.
DTS01 deluge protection certified by ITS.
Operating temperature range -60°C to +100°C as standard.
>>>
View the product on ehawke.com
Hawke Groupe - HUBBELL
AEROSTAT CABLE
Tethered Aerostats are unmanned non rigid lighter than air cehicles sometimes referred to as 'blimps'. These Aerostats remain anchored to the ground by a thether cable. This tether cable provides
electrical power to the platforms systems, radar, infrared , CCTV, etc via fibre optics (fiber optics). The tether cable can also act as the main tensile rope, this involves the use of aramid fibres which act as the strength member enabling the cable to withstand snatch loads of several tonnes.
The tethered aerostat (TA) consists of the envelope with the ballow, the payload suspended by rope and rigging. The payload would include navigational equipment, control and emergency power and lightning discharge protector. Working altitudes can vary from 1000-5000 meters with payout speeds of up to 180 meters per minute.
The cable construction uses Fibre Optics (Fiber Optics) and conductor cores and coaxials, these elements are wrapped in aramid bibres like kevlar (tm) or Twaron that acts as the strength member normally rated 4-5 times the safety margin with limited elongation of less than 3%. The entire package is extruded with a waterproof protective material such as polyurethane. The cable diameters are between 12-19mm diameter.
The strength element aramid fibre is terminated in a lightweight eye thimble to a padeye and the conductor elements pig tailed out the dise of the tether to special waterproof connectors. All these components can be made in delrin peek or aluminium for reduced weight implications.
Objective design for Aerostat cables and important characteristics are material stiffness and strength to weight ratio (B/D ratio). The diameter of the tether has to be as small as possible to reduce or limit the aerodynamic drag.
>>>
View the product on hydrohouse.co.uk
HYDROBOND ENGINEERING LTD
CABLE TRANSFER SET - THROWMASTER 102A
The Throwmaster Cable Test Set Model 102A is a portable, battery powered instrument for field testing and transfer of metallic telephone cable pairs. It is normally used by technicians as their
primary test set. All functions normally associated with the testing of wire pairs and transfer service may be accomplished using the Throwmaster 102A. Features: Accurately measures opens: (up to 100,000 feet) as well as voltage and resistance. Supplies talk battery: Using a unique signaling function, talk battery is supplied and communication established. Handsets or headsets may be used at both ends. Tests spare pairs: Utilizing the same functions as a field test board, tests may be made for shorts, grounds, crosses, opens, splits and high resistance faults. Tests Working Lines: Working lines may be tested for status of busy, idle, reversed, or special voltage Sends simplex 577 Hz Tone: For pair identification which is silent to subscribers. Tone Buzz Around: Normally used prior to pair transfers, the Buzz feature allows technicians to test old and new pairs simultaneously for defects and continuity.
>>>
View the product on jmwlimited.co.uk
JMW Limited
