Selection of 1 products among
1
MSN8100-H HF SOFTWARE DEFINED RADIO
The performance characteristics
described are pertinent to any
one channel to the extent
described, all channels being
mutually independent.
Frequency Range:
Rx 10kHz to 30MHz in 1Hz steps
Tx
1.5MHz to 30MHz in 1Hz steps
Tuning time:
< 5ms to within 20Hz
Frequency accuracy:
3 parts in 10 (0° C to 35°C)
External Frequency input:
1, 5, or 10 MHz
Modes of Operation:
CW A1A, A1B
MCW A2A, A2B
AM H3E
FAX F1G, F3C
FSK F1A, F1B, J2B
USB/LSB H2A, H2B, J2A, J2B,
J3E, R2A, R2B, R3E
ISB B7B, B8E, B9W
STANAG 4197, 4198, 4203,
4285, 4415, 4481,
4529, 4539, 5031,
5511 & 5522
compatible
The SDR is configurable to support both
half duplex and full duplex operation (in
data modes using a combination of two
channels)
Equipment Status and BITE:
Indicator display for equipment operability
Interrogatory BITE with detection to
module level
Channel store:
1024 pre-sets per channel. Parameters
stored in non-volatile memory include
frequency, mode, AGC characteristics,
filter selection, BFO/RIT and transmitter
power
In-band noise:
-50dBc in a 3kHz bandwidth
Wideband noise:
The noise level is 60dB
Unwanted sideband suppression:
>60dB
Spurious emissions:
Better than -80dB at all frequencies
removed by more than 5% from the tuned
frequency (with PPS)
Sensitivity:
LSB, USB, ISB; a signal of -113dBm (1mV
emf) in a 3 kHz bandwidth gives a
(S+N)/N of 10dB.
A high sensitivity position is provided
AGC:
100dB below the wanted signal
Spurious rejection:
At frequencies more than 20kHz from the
tuned frequency; at least 80dB and
>105dB, at frequencies >5% (with PPS)
Internally generated spurious:
Fewer than fifty 3kHz channels above -
121dBm referred to the input. No channels
have spurious responses above -112dBm
Mute and De-sense:
When PTT is operated, receiver output is
muted
Scan mode:
Channel scan between designated
channels with selected dwell time on each
channel (0.1s to 12.7s).
Receiver Antenna input:
Impedance; 50 Ohms nominal, no damage
is caused by input signals of up to 100V
emf from a 50 Ohm source. The level of
any radiated frequency component does
not exceed -87dBm
AF Outputs:
Two line outputs for each channel, level
adjustable from -20dBm to +10dBm into
600
Ohms balanced. User facility to switch the
lines to either sideband
AF Inputs:
One line input for each sideband, level
adjustable from -20dBm to +10dBm into
600 Ohms balanced. User facility to switch
the lines to either sideband
Tape recorder:
Open collector gate
Exciter RF Output:
Load impedance 50 Ohms; output 17dBm
±1dB
PA Interface:
RS-422 serial control
Precision Time and Frequency Standard:
To STANAG 4430
Transmission Signalling:
Ready; Busy and PTT; all at 0V when
activated
Local Audio:
One input and output at 0dBm/600 Ohms
Data Input/Output:
RS-422 with handshaking
Remote/Local Control:
i) RS-232 serial point to point
ii) 10/100 Base T Ethernet (main control
port)
Power Supply:
85-132 and 170-264 VAC autoranging,
47-63 Hz
Power Consumption:
350 VAmax; four channel configuration
Temperature range:
MIL-STD-810F. Methods 501.4 and 502.4
Operating: -6°C to 49°C
Storage: -33°C to +71°C
Humidity:
MIL-STD-810F Method 507.4
Vibration:
MIL-STD-167-1 (ships) Type 1
Shock:
MIL-STD-810F Method 516.5
15g, 18ms
EMC/EMI:
MIL-STD-461E
MTBF:
MIL-HDBK-217F at 25°C NS > 4000 hours
Size:
178H (4U) x 483W x 495D mm
(ex. handles)
Weight:
17kg max depending on configuration
• Multi-channel, multi-mode operation
• Outstanding radio performance
• Embedded modem supports current and future
waveforms and services
• High data rate and networking waveforms enabling
• Naval Intranet over HF
• Open, menu-driven Human Interface
• Software configurable ready for in-service upgrade
• Standard interfaces support legacy integration
• Supports cross service interoperability
• Networked via Ethernet and SNMP
• A future-proof procurement
>>>
View the product on thales-communications.ltd.uk/signature_management.htm
THALES JOINT SYSTEMS
