Associated devices: suppliers, wholesalers and manufacturers on Hellopro
Search   


Associated devices :

757 products
Select the category
Selection of 40 products among 757
DATA ACQUISITION DEVICE PLUG-N-DAQ.

DATA ACQUISITION DEVICE PLUG-N-DAQ.
A compact 2channel in/out data acquisition device for recording and analysis. Utilising standard USB1.1 interface and requires no driver installation. In addition to AC inputs it directly supports IEPE-type sensors, such as microphones and accelerometers. The outputs may be used for monitoring, playback or signal generation. SPDIF I/O is additionally supported. Filters on the input and output and instrumentation-quality amplifiers ensure reliable 16-bit data. Bandwidth up to 24KHz per channel and simultaneous sampling are supported. >>>
View the product on recordingsystems.co.uk Recording Systems Ltd
COUNTER - CUB5

COUNTER - CUB5
Dual Counter or Counter/Rate Indicator 39 mm x 75 mm 8 Digit, 0.46" (12 mm) LCD LCD, Reflective, or User-Selectable Green/Red LED Backlighting Preset Capability with Optional Output Card Optional Serial Communications Module (RS232 or RS485) Ability to Change Display Color at Preset Front Panel Programming Decimal Points and Scaling 10 - 28 VDC Power Up to 20 KHz NEMA 4X/IP65 >>>
View the product on redlion-controls.com Red Lion Controls Bv
DENSITY METER - DMA 38

DENSITY METER - DMA 38
Features & Benefits The DMA 38 is a small and easy to use bench-top density meter. Sample viscosity, surface tension and color have no influence on the measuring results. The DMA 38 is ideal for replacing hydrometers, aerometers and pycnometers. Typical applications include QC and rapid product identification in the food, beverage, pharmaceutical and petrochemical industries. The DMA 38 requires very little sample and performs a measurement quickly and accurately to 3-digits. A built-in solid state thermostat automatically ensures stable measuring temperatures between 15 and 40°C. >>>
View the product on anton-parr.com Anton Paar Ltd
DIGITAL SOIL MOISTURE TESTER KS-D1

DIGITAL SOIL MOISTURE TESTER KS-D1
The KS-D1 Digital Soil Moisture Tester, used with the GB-1 Gypsum Soil Blocks, make up a valuable system to monitor the soil moisture available to the plants. This system eliminates guesswork so that irrigation can be effectively scheduled according to plants' requirements. The KS-D1, housed in a rugged ABS plastic case, features reliable temperature stable semi-conductor technology with internal battery and calibration checks for users' full confidence. A membrane switch panel provides positive, tactile feel. Spring-loaded binding posts allow for positive contact with the blocks' leads. Specifications: Range: 0.1 to 15 Bars Tension Display: 3 1/2 “ Digital LCD with 0-100 Arbitrary Scale Size: 2 3/4” x 4 3/4” x 1 3/4”” Weight: 8 oz. Battery: 1-9V Carrying Case: included >>>
View the product on delmhorst.com Delmhorst
FLASH 96 N 85÷265V ENERGY ANALYSER

FLASH 96 N 85÷265V ENERGY ANALYSER
Cod. PFE405-50 Large high-contrast LCD display with backlight. Single-phase, 2-phase , balanced or unbalanced 3-phase (max. 500V ph-ph), 2, 3 & 4 wire LT and HT systems, ../1-5A CT input. Class 1 accuracy on energies (EN61036), RMS measurement up to the 31st harmonic. Equipped with 2 digital outputs programmable for Alarm or Pulse transmission (or as remote Output devices) and with 2 expansion ports for connection of external transmission modules Modbus protocol. Suitable for harsh environment. Temperature range -20+60°C. Flush mount 96 x 96 mm. >>>
View the product on electrex.it ELECTREX
TEMPERATURE LOGGERS - DL8808 WATERPROOF

TEMPERATURE LOGGERS - DL8808 WATERPROOF
DL8808 Waterproof Temperature Data Logger with RS232 or USB Port Features Rugged, waterproof housing User-defined min/max alarm setting Start/stop logging by programmed schedule or internal magnetic switch Specifications Data collection: up to 8,000 temperature datas DataTemperature range: -40° to 185°F (-40° to 85°C) DataCable length: 150 cm with DB9 connector DataSample interval: prog. from 1 sec. to 2 hours >>>
View the product on linseis.net Linseis
SMARTSCOPE APEX 200 MEASUREMENT

SMARTSCOPE APEX 200 MEASUREMENT
SmartScope® Apex is the measurement solution for high magnification video and multi-sensor applications. Versatile auto-sensing quick mount lenses offer on-screen magnifications from 84x to 2100x. Sturdy granite support columns maintain the physical stability needed for such high magnifications while 0.04_m XYZ scales provide the necessary resolution. Fitted with optional DRS™ Laser, Rainbow™ or Feather™ probing this stable, robust metrology platform will characterise the most intricate of components to the highest of accuracies. SmartScope® Apex comes with the powerful MeasureMind® 3D multi-sensor metrology software with full three dimensional functionality. Easily control lighting, magnification and edge detection to measure and reports of features. Select and store images in digital format for visual defect analysis. Machine Features Manual and fully automatic operation High resolution and magnification Automatic edge detection Sub-stage, Coaxial through the lens and Fibre optic ring illumination Fully featured, programmable MeasureMind 3D™ three dimensional multi-sensor metrology software Auto-focus facilitating accurate Z measurement Image collection and storage Optional Multi-Sensor capability including Laser, Touch, Rainbow (White Light) and Feather probing Optional software: MeasureFit® Plus - Part to CAD analysis SmartReport® Plus - Custom Report Generator MeasureMenu™ - Single Touch Operator Front End SmartCAD® - Off-Line Programming from CAD Scan-X® - Surface scanning an analysis Product Specification Measuring Range (X,Y,Z) 200 x 200 x 100mm Extended Z 200 x 200 x 150 mm Machine Dimensions (DWH) 99 x 107 x 181 cm, 1450Kg Scale Resolution 0.04µm Motor Drives DC servo with 3 axis joystick (X, Y, Z, Zoom) Worktable Granite with fixture holes, stage glass and 10 Kg load capacity Lens Precision fixed objective, 2.5x with 2.0x doubler (210x on-screen*) Lens Attachments Optional Precision fixed objective, with 2.0x doubler: 5.0x (420x on-screen*), 10.0x (840x on-screen*), 25.0x (2100x on-screen*), 50.0x (4200x on-screen*) Illumination Substage (backlight) coaxial (through-the-lens) surface, fibre optic ring light Camera 1/2” format colour CCD with 768 x 494 pixel array Image Processing 256 level greyscale processing with 10:1 sub-pixel resolution Multisensor Options DRS Laser, Grid Projector, Feather Probe, Rainbow™ Probe * Onscreen magnification depends on monitor size. Figures shown are for a typical 15” LCD monitor. Power Requirements 100-240 vac ± 5%, 50/60 Hz, 400 W Rated Environment 18-23°C ± 2°C/hr, 30-80% humidity (non-condensing), vibration >>>
View the product on ogpuk.com OGP UK Ltd
MODULAR CALIBRATION SYSTEM - SYSTEM 1000

MODULAR CALIBRATION SYSTEM - SYSTEM 1000
Calibration and testing of pneumatic and electronic industrial instrumentation in the most common and pressure and electric ranges. Instruments to be checked with system 1000 are typically: Electronic and pneumatic pressure and differential pressure transmitters; Electro-pneumatic converters; Indicators, recorders, controllers either pneumatic or electronic type; Pressure switches; Pressure gauges and others. Compact design and low cost make this system especially suitable for routine operations and also for training purposes. >>>
View the product on scandura.it SCANDURA & FEM
ELECTRONIC DIGITAL POSITION INDICATOR - AP04

ELECTRONIC DIGITAL POSITION INDICATOR - AP04
Electronic position indicator with bus interface for target / position value and programming parameter transmission. Very compact size with through hollow shaft for easy mounting onto the machine spindle. AP04 is an absolute position indicator, ie. capturing movements made when power off. Features * Compact size * Through hollow shaft, max. diam. 20mm * With integral interface RS485 * Reset, incremantal measurement and offset via keyboard * Robust magnetic sensorics. >>>
View the product on siko.de SIKO
HB400 HORIZONTAL BENCHTOP MEASURING PROJECTOR

HB400 HORIZONTAL BENCHTOP MEASURING PROJECTOR
Superlative in design and function, the HB400 is ideal for the most demanding applications in optical measurement. The HB400 features a 16? (400mm) screen diameter. Features, Specifications & Options * Vertically correct image * Fully useable 16? (400mm) diameter screen with crosslines and calibration marks * Heavy-duty, metal construction * 12? x 6? (300 x 150mm) measuring range (extended 16? X-axis measuring range iavailable) * 21.25? x 5.125? (540 x 130mm) staging area * Dual fixturing slots * Screen-mounted overlay chart clips * 110 lb. (50 kg) weight capacity * Dual intensity (hi/low) tungsten halogen profile illumination * Twin-bundle, adjustable on-axis, fiber optic surface illumination * Operator glare shields for surface illumination * Helix angle stage adjustable +/- 15? * Quick-change, bayonet style lens mount * Q-Axis displayed in digital readout * Built-in digital protractor with DD/DMS conversion * Heidenhain .00005? (0.001mm) resolution scales * Centrally mounted vertical (Y-axis) scale (in-line with lens/workpiece) * Threadless X-axis quick release for ?zero? backlash * Protective guideway covers for both X and Y axes * Available with a wide range of readout systems/software options * Swing-away lamphouse (optional) * Optical edge detection (optional) * 10x, 20x, 25x, 31.25x, 50x, and 100x magnifications available * Available in manual, motorized, and CNC configurations * Available with OV2, Starrett's innovative Optical-Video Adaptor Specifications subject to change. >>>
View the product on starrett.com STARRETT
AUTOMATIC WATER SAMPLERS - 3710 COMPOSITE-ONLY PORTABLE SAM

AUTOMATIC WATER SAMPLERS - 3710 COMPOSITE-ONLY PORTABLE SAM
Single-bottle sampling up to 4 gallons The 3710 Sampler combines simple operation and high volume capacity for single-bottle sampling. It collects composite samples - based on time or flow intervals - in a 2.5 gallon glass or polyethylene bottle, or a 4 gallon polyethylene bottle. Up to 24 sampling stop and resume times can be preset for unattended, automatic sampling. Setup and programming is a snap. Simply choose the options you need from the selections displayed on the two-line, backlit LCD. >>>
View the product on isco.com Teledyne Isco Groupe - Teledyne Technologies Incorporated
CALIBRATION SYSTEMS-MODEL 100

CALIBRATION SYSTEMS-MODEL 100
The Model 100 calibration system consists of a uniform heating plate, controller, and Type K thermocouple that is used to heat and test metal samples over the temperature range of ambient to 950°F (510°C). This system provides a fast and simple offline method to verify the accuracy of infrared sensors and thermocouple probes on specific test samples. It is used to determine the proper TRUSET setting, SIF (Surface Index Factor) adjustment, and/or emissivity of a surface by using a thin wire thermocouple embedded in the test sample. It is commonly used as a reference source for characterizing aluminum and other low emissivity materials plus it can be used as an approximate blackbody reference when looking at a flat black painted metal surface. This calibration system eliminates the uncertainty regarding application errors associated with surface emissivity. >>>
View the product on williamsonir.com WILLIAMSON
JOFRA ASC300 - ADVANCE SIGNAL CALIBRATOR

JOFRA ASC300 - ADVANCE SIGNAL CALIBRATOR
The ASC300 is substantial enough to cover all your needs for a process signal calibrator with superior accuracy and compact enough to fit into your tool box and operate with one hand for easy field calibration. The ASC300 can change your entire calibration regimen for signal, pressure, and temperature. You can combine this versatile calibrator with the JOFRA APM external pressure modules or a JOFRA dry-block calibrator to meet your calibration needs. >>>
View the product on jofra.com AMETEK Calibration Instruments
AC CURRENT DIGITAL PANEL METERS - MODEL ACI-J

AC CURRENT DIGITAL PANEL METERS - MODEL ACI-J
The ACI-J is an economical, easy to use 1/8 DIN screwdriver scalable (Zero & Span pots) AC digital panel Voltmeter for display-only applications Input ranges Jumper switch selectable: 0-1.999 mA 0-19.99 mA 0-199.9 mA 0-1.999 A 0-5.00 A Digits 3 1/2 digits [?], 14mm high. Legible up to 7 metres away. Digit colour Red or green (variable brightness option available) Scaling Zero and Span potentiometers Filtering Fixed 0.5 Second basic filtering. 1.0 Seconds on True RMS version Front panel controls Zero and Span potentiometers. Decimal point position jumper switch. >>>
View the product on london-electronics.com London Electronics Limited
IBS HEAVY - MULTICOR® K AND MULTICELL

IBS HEAVY - MULTICOR® K AND MULTICELL
Pulverised coal feeding requires economic efficiency, quality and maximum reliability. The parameters are based on the interplay of overall system engineering, material discharge, feeding and pneumatic material transport. Optimal pulverised coal feeding in three steps Perfectly matched system components are a basic requirement for optimal three-step pulverised coal feeding. This is realised in a pressure-proof mass-flow feed system using the Coriolis principle with a horizontal star feeder. >>>
View the product on schenckprocess.com Schenck Process UK Ltd
HIGH PERFORMANCE DATA LOGGER - SL2100

HIGH PERFORMANCE DATA LOGGER - SL2100
SL2100 High Performance Data Logger The SL2100 is a high performance data logger with 16 bit resolution. It has eight channels that can be configured via software to accept mA, mV, low level DC voltage and thermocouple sensors. Although mains powered, the SL2100 has internal batteries that will last eight hours in the event of a power failure. There is enough internal memory to log 112,000 readings at sample rates from once per second to once per day in one second increments. The SL2100 can be configured to log "off-line" to its own internal memory, or, if connected to a computer, "on-line". Where the data are stored on the hard disk of the computer. Specifications SL2100 Power Mains convertor - 12-15DC @ 400mA Battery Back Up Yes Temperature Range -20°C to +50°C Inputs Voltage ±10VDC, ±1VDC, ±100mV, ±50mV Accuracy - Voltage Input ±0.04% of full scale Current ±20mA Accuracy - Current Input ±0.04% of full scale Thermocouple Types B, E, J, K, N, R, S & T Accuracy - Thermocouple Input ±0.5°C + 0.04% full scale Digital Inputs 3 Digital Type Volt free contact or TTL - Switch state or Accumulator Mode Number of Readings 112,000 Digital Outputs One - Maximum Voltage 20v Maximum Current 100mA Sample Rate 1 seconds to 24 hours in 1 second steps Ingress Protection IP50 Software Alarms Yes Delayed Start No Stop When Full Yes Material Extruded Aluminium Warranty 1 Year Dimensions (LxWxH) 247mm x 110mm x 36mm >>>
View the product on signatrol.co.uk Signatrol Data Logging
PRESSURE TEST & CALIBRATION VACUUM PRESSURE COMPOUND TYPE

PRESSURE TEST & CALIBRATION VACUUM PRESSURE COMPOUND TYPE
Standard models available: Model Pressure Range DTPN020 -0.1 to -0.005 MPa, or 0.005 to 0.25 MPa DTPN021 equal mbar DTPN022 equal inH2O DTPN060 -0.1 to 0.6 MPa DTPN061 equal mbar DTPN062 equal inH2O DTP0060 0.04 to 0.6 MPa DTP0061 equal mbar DTP0062 equal inH2O Accuracy: Standard 0.050% of reading, Optional 0.025% of reading. Start Pressure: Standard 5 kPa (50 mBar). Minimum Weight Increment: Standard 5 kPa (50 mBar), Optional lower increment upon request. >>>
View the product on henryautomation.com Xian Henry Automation
METERING MACHINES A COMPACT

METERING MACHINES A COMPACT
The new Cannon A-Compact high-pressure metering machine provides a compact, economical solution for the production of quality polyurethane products. This competitively-priced model is designed for polyurethane manufacturers whose simple, two-component process, or lower production rate, does not require the complexity and additional cost associated with a more advanced metering machine system. >>>
View the product on cannonsolutionsuk.com Cannon Solutions (UK) Ltd
HAWKEYE BLUE FLEX

HAWKEYE BLUE FLEX
Hawkeye Blue Flex — 8mm 4-way Articulation — A new addition to our Hawkeye Blue Flex line is the 8mm diameter, 1800mm long flexible with 4-way articulation. The flexible borescope offerings also include smaller diameters and longer lengths. For small diameter applications and where articulation is needed, choose a Hawkeye Blue Flexible. These scopes are available in diameters from 0.098" to 0.236" and lengths from 27.5" to 70.8". They all have +/- 120°, 2-way articulation and high resolution leached fiber bundles for high contrast images. Fields of view are 45° or 90° depending upon model. >>>
View the product on gradientlens.com Gradient Lens
HIGH-SPEED COUNTERS WITH PRESETS, - DX345 - DX348

HIGH-SPEED COUNTERS WITH PRESETS, - DX345 - DX348
Universal multi-function counter with multiple operation modes as counter, display of RPM, speed, cycle rate, baking and processing time and timer/stopwatch functions. DX345: display counter only DX346: counter with display and analogue output DX347: counter with display and 2 presets (optocoupler outputs) DX348: counter with display and serial RS232 / RS485 interface Dimensions 96 x 48 mm and 6 decade LED display at 15 mm size Universal inputs for sensors with PNP/ NPN or Namur characteristics Easy scaling and setup by means of 2 front keys and menu support Counting frequency 100 kHz (A/B quadrature count) Selectable linearisation functions with all operation modes Power supply 115 / 230 VAC or 18 – 30 VDC in one unit Aux. output 24 VDC / 150 mA for supply of sensors and encoders >>>
View the product on mks-control.com MKS Maschinen-Kontroll-Systeme
DETECTOR TOXIC GAS - GASALERTMICRO 5 PID - IAQ MONITORING

DETECTOR TOXIC GAS - GASALERTMICRO 5 PID - IAQ MONITORING
The GasAlertMicro 5 PID is a handheld instrument for measuring VOCs.VOCs include building materials, paints, paint strippers, solvents, wood preservatives, correction fluid, aerosol sprays, cleansers, disinfectants, air fresheners, adhesives, stored fuels and automotive products. Office equipment such as copiers and printers.The human health effects include eye, nose and throat irritation; headaches; loss of co-ordination; nausea; or damage to liver, kidney, and central nervous system. Features: * Smaller and over 50% lighter than competitive instruments * Water-resistant design in an integral concussion-proof enclosure * Continuous LCD shows simultaneous gas concentrations for five gases * 0 - 1000 ppm measurement of VOCs (Volatile Organic Compounds) * Data Logging Capability >>>
View the product on wessexpower.co.uk Wessex Power Technology LTD
THERMADATA LOGGER™ - MODEL TB

THERMADATA LOGGER™ - MODEL TB
ThermaData Logger™ - model TB Mk II series portable data-logger - blind with one internal temperature sensor • waterproof housing - IP66/67 protection • designed to meet EN 12830, S & T, C & D, 1 • temperature range -40 to +85°C • high resolution 0.1°C, high accuracy ±0.5°C The new Mk ll series consists of a comprehensive range of portable data-loggers utilising the latest in electronic technology. The new ThermaData loggers are housed in a waterproof, ergonomic case that is designed to meet IP66/67 protection. The ThermaData logger Mk ll range offers the customer the choice of either blind data-loggers or data-loggers with a LCD display. Other options include internal and external temperature sensor/probe The external probes can be either fixed or detachable via a waterproof three-pin connector. The remote temperature probes are supplied with a one metre PVC/PVA lead. Each logger incorporates a red and green LED, the flashing green LED indicates that the logger is active/logging and the flashing red LED indicates that your customised pre-set alarms have been exceeded. Communications are via a USB cradle that is supplied with the ThermaData Software. Please note: when ordering loggers it is necessary to order at least one ThermaData logger cradle. >>>
View the product on etiltd.co.uk Electronic Temperature Instruments Ltd
1900 FLOW CALIBRATORS

1900 FLOW CALIBRATORS
Precision Instruments for Pressure, Flow, Temperature and Level Summary Use with Laminar Flow Elements, Accutube averaging pitot tubes, Orifice Plates, Venturis, Vortex, Turbines or other flow meters Corrects for density and viscosity changes bases on pressure and temperature inputs Windows set up Calculates corrected or actual flow rate and total Analog, relay and digital outputs >>>
View the product on meriam.com Meriam Instrument
ELCOMETER 107 CROSS HATCH CUTTER

ELCOMETER 107 CROSS HATCH CUTTER
The coating may be continuous and look good, but how well is it connected to the substrate? The Elcometer 107 Cross Hatch Cutter provides an instant assessment of the quality of the bond to the substrate. Due to is rugged construction this gauge is ideal for thin, thick or tough coatings on flat or curved surfaces. An ideal field or laboratory test. Low cost Easy to change cutters Ideal for thick or hard coatings Large selection of cutters, each with four cutting faces Can be converted into the Elcometer 141 Paint Inspectors Gauge (P.I.G.) Robust design Large Non slip grip The Elcometer 107 Cross Hatch Cutter is available in two versions. The Basic Kit comes complete with: Robust handle, the cutter of your choice (see below), Allen Key (wrench), presentation storage case and instructions (together with the Classification of Adhesion Test Results Chart) The Full Kit includes all that is supplied in the Basic Kit, and also includes: An eye glass, brush, and adhesive tape (either ASTM or ISO tape), all in a plastic ABS carrying case. >>>
View the product on protovale.co.uk PROTOVALE (OXFORD) LTD
DC CURRENT AND VOLTAGE CALIBRATOR - MINICAL® IV

DC CURRENT AND VOLTAGE CALIBRATOR - MINICAL® IV
Designed for the calibration of process control instrumentation including transmitters, transducers, recorders, controllers and indicators, the Minical IV is a highly accurate mV/mA simulator/calibrator with the added ability to generate up to 12V DC and to read up to 20V DC. In addition, the Minical IV can act as a 4 - 20mA transmitter simulator, which will operate in powered or unpowered loops. Data entry is via a scratch resistance, splashproof membrane keypad system with fast and slow increment /decrement keys providing rapid and precise output value settings. The Minical IV DC Current and Calibrator is supplied complete with a UKAS Calibration Certificate, carry case, test leads and battery charger. Features High accuracy (±0.025% F.S.D.) and reliability Robust and hard-wearing Supplied complete with UKAS certificate >>>
View the product on haven.co.uk Haven Automation
Q-FOG CYCLIC CORROSION TESTERS

Q-FOG CYCLIC CORROSION TESTERS
Three EnvironmentsThe Q-Fog can cycle through three functions: fog, dry-off and humidity. Simple tests may consist of cycling between fog and dry. However, more complex procedures (such as automotive) call for multi-step cycles incorporating humidity or condensation, along with salt fog and dry-off. Q-Fog is available in model SSP for Prohesion or conventional salt spray, and model CCT for corrosion research and cyclic automotive tests.Simple to Use The Q-Fog features a custom controller that allows the operator to easily program complex tests or a range of pre-programmed procedures. The built-in self diagnostics warn the operator when to perform routine maintenance (e.g., refill the solution reservoir) or to check for operation. >>>
View the product on q-lab.com Q-Lab Europe Ltd.
MULTI-FUNCTION POWER MONITORS CM485

MULTI-FUNCTION POWER MONITORS CM485
The CM485 uses Jbus/Modbus protocol (although other protocols are available on request), and up to 32 units may be connected to a bus system, which is expandable to 255 when repeater units are used. Two CM485 units may be used as a repeater by connecting them back to back after each 32 units. Features: * Input from NEMO interface DI1 3-wire * Serial asynchronous transmission * Baud rate up to 9600 * Auxiliary supply 115/230Vac >>>
View the product on rayleigh.co.uk Rayleigh Instruments Ltd
OIL & GAS MEASUREMENT - DUALSTREAM I ADVANCED SUBSEA

OIL & GAS MEASUREMENT - DUALSTREAM I ADVANCED SUBSEA
Dualstream I advanced Subsea Subsea Experience Dualstream I meters have been implemented in shallow diver accessible depths and in deepwater water applications in up to 3000m water. The fi rst subsea Dualstream meter was installed in 1994. Key Benefi ts • Intelligent on-line measurement • Simple, cost effective and robust fl ow spool • Tried and tested instrumentation • Simple Data Acquisition System • Signifi cantly reduced operational costs • Digital communications enabling reduced size and weight of subsea meters • Large installed base including allocation systems Applications Reservoir management • Optimise production • Remote well monitoring • HC gas and condensate fl ow rate measurement • Water breakthrough detection Production allocation • Royalty allocation • Essential for economic development of marginal fi elds Background Wet gas measurement is now an integral part of most gas condensate fi eld developments. Dualstream wet gas fl ow meters have been utilized in over 100 projects since the early 1990’s and have been a key factor in enabling marginal fi eld development providing wet gas allocation measurements and enhancing reservoir data. Dualstream I advanced (Subsea) Solartron ISA’s advanced version of the Dualstream I meter includes an additional differential pressure measurement to enable on-line detection of changes in liquid fraction. This system can be used to reduce period well testing or to calculate liquid fl ow rates in real time thus alleviating the requirement for well testing altogether. For this reason Dualstream I advanced is particularly applicable to subsea fl ow rate measurement in reservoir management, allocation of hydrocarbon gas and condensate and as an economic method of water breakthrough detection. Measurement Technique • Dualstream Venturi, Pressure loss ratio measurement, wet gas correction algorithm and PVT calculation Mechanical Specifi cation • Standard Line Sizes 2” NB to 24” NB (larger sizes on request) • Pressure Class API 5K/10K API (15K & ANSI ratings on request) • Process Temperature Range -20 to 120°C (-4 to 248°F) (higher ranges on request) • Meter Body Material Duplex uns531803 as standard • Weight dependant on NB/Pressure rating • Overall length 5D (typical) Installation Requirements • Upstream Straight lengths – 3D to 10D (typical) (calibrated spool supplied for allocation systems) • Downstream Straight lengths – None (5D calibrated spool supplied with thermowell for allocation systems) • Orientation Horizontal Performance • Uncertainty – Gas Mass Flow Rate 2% (typical) – Liquid ±10-20% – Condensate PVT calculation water ±1 am3/h (water or oil continuous fl ow) • Repeatability – Gas Mass Flow Rate >>>
View the product on solartron.com Solartron Mobrey Ltd




  Search    
 
 
 
Search
See all of the sector's products : Measuring devices, analysis and sensors