Analysis electrodes and waves: suppliers, wholesalers and manufacturers on Hellopro
Search   


Analysis electrodes and waves :

13 products
Select the category
Selection of 13 products among 13
SVP370 SCANNING VIBRATING ELECTRODE SYSTEM

SVP370 SCANNING VIBRATING ELECTRODE SYSTEM
Electrode Technique (SVET) operates with a non-intrusive scanning, vibrating probe measuring and mapping the electric field generated in a plane above the surface of an electrochemically active sample. This enables the user to map and quantify local electrochemical and corrosion events in real time. The SVP370 vibrating probe system provides you with increased electrical sensitivity as well as enhanced system stability. Localised corrosion events of less than 5µA/cm2 can be measured with this extremely sensitive technique. The probe vibration is controlled by a piezoceramic displacement device allowing vibration amplitudes from 1-30 µm (perpendicular to the sample surface). It is an ac technique, thus, high system sensitivity is achieved via a differential electrometer in conjunction with an integrated lock-in amplifier. All system parameters, including the xyz scanning mechanism, piezo actuator, and lock-in amplifier are controlled via a PC under the user friendly Windows™ operating system. >>>
View the product on uniscan.com Uniscan Instruments
MEASUREMENT SYSTEM CUSTOM SG

MEASUREMENT SYSTEM CUSTOM SG
SATIMO’s multi-probe SG systems are based on modular technology blocks and can be customized to fit specific applications. Probe arrays for frequencies down to 70MHz and up to 18GHz are available and can be arranged in various configurations depending on the antennas to be tested. Electronic scanning of the probes in a probe array can be combined with mechanical scanning of the entire array, or the antenna under test, for fast and unlimited spatial sampling. Probe arrays can also be combined with classical single probe mechanical scanners for frequencies up to 40GHz. The possibilities are endless; please contact SATIMO for a solution to your antenna testing needs. >>>
View the product on satimo.com Satimo Main Office
FG/BA BALL PROBE

FG/BA BALL PROBE
FG/BA Ball Probes Two fundamental criteria for a good test are repeatability and resolution for comparision between results. In many cases, where sample hardness/softness is required, a ball probe can provide both repeatability and resolution. The principle of the ball probe is that uniform compression force is distributed at a normal angle to the surface area of the ball. This gives an averaging effect over the local area being tested Capacity 50.9 kgf, 500 N, 112.5 lbf Packaging Ball probe - ball diameter must be specified. Applications Ball probes are invaluable for performing a wide variety of texture analysis tests. They are used in many applications where specimen hardness or softness is required. They are ideal for testing fruit, vegetables and confectionery products. For specimens where the application requires the product to flow, for example cream cheese being squeezed from a tube, gels, pastes etc., it is possible to contain a sample in a container and penetrate the sample with the ball probe. >>>
View the product on lloyd-instruments.com Lloyd Instruments Ltd.
ENVIRONMENTAL TRI-CELL SYSTEM

ENVIRONMENTAL TRI-CELL SYSTEM
Environmental Tri-Cell is designed for use with the Model 370 Scanning Electrochemical Workstation system. Its' various configurations will allow users to change samples without moving the scanning head and reduce the volume of electrolyte required for scanning probe electrochemistry experiments. The system can also be used for controlled atmosphere or liquid flow experiments due to its four inlet/outlet purge ports, using an optional rubber gaiter sealed cover. Tri-Cell incorporates an extremely flexible sample accommodation platform, designed to take as wide a range of sample configurations as possible. The 'pick and mix' system allows the user to decide on exactly the configuration required and to then order the optimum system components. Listed below are the components available for any desired configuration Triangular perspex base plate, 316mm side length. Part no: ECTB336 Base plate level adjusters, 33mm extension range (3 required). Part no: ECLA50M6 Glass cell, 143 x 60mm, including gas and liquid ports; o-ring seal. Part no: ECGT155D60H Cell clamp for use with ECGT155D60H & ECTB336 (3 required). Part no: ECTC155 Sample holder for 32mm diameter metallurgical samples. Part no: ECSH32 Flexible cell sealing gaiter for ECGT155D60H & standard probe. Part no: ECSG155 PTFE sealing disk for ECGT155D60H base to allow use of organic electrolytes. Part no: ECPD155 Reference electrode clamp/holder. Part no: ECREC155D60H Auxiliary electrode clamp/holder. Part no: ECAEC155D60H Adjustable legs for SP/SVP100 scanning head to stand over cell (4 required). Part no: ECAL100C75B >>>
View the product on uniscan.com Uniscan Instruments
PH METER CRIUS 100

PH METER CRIUS 100
PH meters are one of the most common analysers in use today on water treatment and process plants and yet online pH meters cause continual problems for their operators. What is needed is a reliable, self-cleaning, self-calibrating pH meter for a reasonable cost. That is exactly what you get with the CRIUS 100 and CRIUS 100+ process pH analysers. The pH sensor at the heart of the Process Instruments online pH meter is a K-series polymer filled glass electrode. This pH electrode is far superior to many pH electrodes on the market and is designed for a long life, low drift and reliability. Unlike many pH analysers, you don't need to search through hundreds of pH electrodes to find one that works in your process as the K-series electrode works in all environments from pH 2 to 12 and in conductivity from 0µs to 10,000µs. >>>
View the product on processinstruments.net Process Instruments UK Ltd
QC1050 EPOXY BODY/PLATINUM CELL

QC1050 EPOXY BODY/PLATINUM CELL
Epoxy Body/Platinum Cell, platinised 12mm x 100mm with waterproof mini-din plug, for use with Star Series Meters. If you require this electrode for a non-Star Series meter please call 01342 820820 or email enquiries@qclscientific.com to discuss the options available. Field & Laboratory use Cell Constant: approx 1.0 (cm-1) Conductivity Range: 1 µS/cm to 20 mS/cm Cable Length: 1.5m Min/Max Immersion: 20/90 mm >>>
View the product on qclscientific.com QuadraChem Laboratories Ltd
MEASUREMENT SYSTEM SG24

MEASUREMENT SYSTEM SG24
The SG24 system is designed specifically to provide fast and accurate measurements per the CTIA specification for Over The Air performance testing of mobile devices. It represents the state of the art, in both technology and cost effectiveness, for cellular terminal test service providers and labs. SG24 has 23 probes, spaced at 15ş in elevation, with an internal arch diameter of 2.4 meters. It shares the same key technology as the SG64 and SG32, which gives outstanding measurement speed and accuracy for antennas and wireless terminals. The system is delivered and installed as a turnkey system, including a shielded anechoic chamber and a PC with measurement software. >>>
View the product on satimo.com Satimo Main Office
FG/CO CONE PROBE

FG/CO CONE PROBE
FG/CO Cone Probes Cone probes are supplied with a range of angles from 15° to 90°. Selecting the appropriate cone is often dependent upon the testing standard being used or based on the consistency of the material to be tested. Capacity 50.9 kgf, 500 N, 112.5 lbf Packaging Cone probe - cone angle must be specified. Applications Cone Probes have been used for many years, particularly on penetrometers, for testing building industry products such as sealants and mastics. >>>
View the product on lloyd-instruments.com Lloyd Instruments Ltd.
MEASUREMENT SYSTEM SG32

MEASUREMENT SYSTEM SG32
The SG32 is a down-scaled version of the SG64, with 31 probes and a 1.5 meter internal probe array diameter. Its compact dimensions make it perfect for office buildings and labs where ceiling height is limited. The SG32 can also be configured for OTA performance testing. Even if the diameter of the SG32 probe array is too small to be CTIA certified, the total measurement uncertainties for both TRP and TIS are still within CTIA specifications. >>>
View the product on satimo.com Satimo Main Office
MEASUREMENT SYSTEM SG64

MEASUREMENT SYSTEM SG64
The SG64 is the standard test solution for antenna design and validation in the cellular and wireless industries. Combined with the SatAct interface, SG64 is compliant with CTIA requirements for Over The Air (OTA) Performance Testing. Several SG64 systems have been CTIA certified. SG64 offers unrivaled testing capacity, far beyond other test systems on the market. It measures full 3D far field radiation patterns and antenna efficiency in just a few minutes, without compromising accuracy. SG64 is available in two standard sizes, with 3.2 meter and 2.4 meter diameters. The 2.4 meter version offers the same capability as the larger version with the exception that it cannot measure the largest antennas. The advantage of the smaller SG64 is that it requires less height in the parent building, see specifications for anechoic chamber dimensions. >>>
View the product on satimo.com Satimo Main Office
MEASUREMENT SYSTEM STARLAB

MEASUREMENT SYSTEM STARLAB
StarLab is the ultimate tool for antenna pattern measurements in labs and production environments where space is limited, cost is critical, and the flexibility of a movable test system is required. With its array of 15 probes, StarLab offers high measurement speed combined with a low-reflectivity measurement geometry for accurate results. StarLab is mounted on wheels, and it is compact enough to go through a standard double door. If needed, one of the two cylinders of absorbers can be removed, allowing it to pass through a standard single door. StarLab is based on SATIMO’s patented probe array technology. Instead of using mechanical scanning of one single probe for radiation measurements, StarLab uses electronic scanning of an array of 15 probes. The only mechanical movement needed to perform a full sphere measurement is a 180° azimuth rotation of the DUT. This means that full 3D radiation pattern measurements can be performed very rapidly compared to conventional single-probe systems. Passive mode measurements of antennas are performed by interfacing the StarLab to a network analyzer. In passive mode, StarLab provides radiation pattern data in any polarization, linear or circular, as well as antenna efficiency. Active mode measurements, commonly referred to as OTA Performance Testing, of mobile phones and other cellular terminals can be performed with the SatAct option. In this mode, StarLab is connected to a radio communications tester. The communications tester sets up a phone call through the StarLab probe array, enabling measurements of radiated Tx power (EIRP) and Rx sensitivity (EIS) over the entire spherical measurement surface surrounding the mobile phone. >>>
View the product on satimo.com Satimo Main Office
MEASUREMENT SYSTEM STARLAB 18 GHZ

MEASUREMENT SYSTEM STARLAB 18 GHZ
Benefiting from the same speed advantage as the basic StarLab but with its upper frequency range extended to 18GHz, StarLab 18GHz is the first step into the future of SATIMO’s higher frequency product offerings. Compared to the standard StarLab, StarLab 18GHz has an additional set of high frequency probes, covering 6-18GHz. These probes are interleaved with the normal 0.8-6.0GHz probes, providing 800MHz to 18GHz of combined frequency range. In the frequency band 0.8-6.0GHz the same specifications of the standard StarLab apply. >>>
View the product on satimo.com Satimo Main Office
MEASUREMENT SYSTEM STARLAB BTS

MEASUREMENT SYSTEM STARLAB BTS
StarLab BTS provides fast, cost-effective and space-saving indoor testing of base station antennas and other linear array antennas. By adding a linear scanner, StarLab is converted from a spherical to a cylindrical near field measurement system. All of the most common BTS antenna parameters can be measured, including gain, directivity, beam tilt, beamwidth, sidelobe levels, cross polar discrimination, and front to back ratio. >>>
View the product on satimo.com Satimo Main Office




  Search    
 
 
 
Search
See all of the sector's products : Measuring devices, analysis and sensors